Mini Classifieds

Pangra wanted
Date: 02/05/2017 01:58 pm
Parting out 77 Bobcat Hatch
Date: 11/06/2017 04:16 pm
Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
WTB - 1979 Fan Shroud - D52E-8246-CIB
Date: 11/05/2020 06:32 pm
Need 4 wheel center caps for 77 Pinto Cruzin Wagon
Date: 10/03/2018 02:00 pm
WANTED Hood Prop Rod
Date: 01/17/2017 02:47 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
hood for a 79-80
Date: 11/30/2018 10:55 pm
95 2.3l short block
Date: 03/18/2017 04:54 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 628
  • Online ever: 2,670 (May 09, 2025, 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 559
  • Total: 559
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

The Restoration Of my 1977 V-6 Pinto Crusing Wagon

Started by DBSS1234, May 07, 2013, 02:48:33 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

DBSS1234

Thanks Cookie. I still plan on having it at Apple Valley for the all ford show in June. Might bring the 77 Cobra also, that way I would have a pair of 77's to show. ;D

Cookieboystoys

I can't wait to see this when done, unbelievable the details and quality... I've seen the stangs, and i know the quality you are capable of...

It's all about the Pintos! Baby!

DBSS1234

Back from a business trip/trade show so I can work on the Pinto again! First picture is of the Steering column and wheel installed. The rest are of the air cleaner. I had a rubber stamp made to redo the part number stamp on the air cleaner snorkle. If any one restoring a 1977 V-6 Pinto out there would like to have the correct stamped number on the snorkle let me know. 1978 Pintos may be the same but I don't know for sure.








DBSS1234

Pinto_one:
I will check diameter of the pulley tonight.
P.S. Ye,p I have to original window sticker. Plan is to get a good color copy of it made and display the car with the copy in the side window. /this will save the original from all the wear and tear plus the sun fading.

pinto_one

Every time you post new photos I got to say wow, this is beyond Restoration . hope you got the dealer sticker to put on the window because its going to look better than new,  but also notice that you car does not have A/C , and been trying to find out the water pump pulley diameter , have two almost tore apart pintos and got the pulleys mixed up, one is smaller than the other , one pinto did not come with a/c and the one I am almost finished with does, also been thinking of making a two grove pulley because the belt broke and ran hot and cracked both heads , this set up always ate belts , also yours does not have the big alt , both of mine do, along with the big 5 blade flex fan from the factory , so if you have time can you let me know what diameter you have , thanks Blaine   (in hot butt Missisippi
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

bbobcat75

BAG VS BOTTLE MAY HAVE BEEN A PLANT THING TOO BOTH MY BOBCATS WHERE MADE IN THE SAME PLANT SO MAYBE THAT IS THE REASON TOO OR LIKE YOU SAID RAN OUT OF BOTTLES AND INSTALLED BAGS TO KEEP THE FLOW GOING!!

TAKE CARE
1975 mercury bobcat 2.8 auto
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

DBSS1234

Quote from: bbobcat75 on January 14, 2014, 06:37:44 AM
dale looks great!!! as far as the washer bottle/reservoir my 75 bobcat hatch back with factory 2.8 has a plastic one just like my 78 wagon with a 2.3 have a super nice one from a 80 if needed!!

take care and great work will be doing that to my 75 in about 20 years when it needs it and I need a project!!

Thanks for the kind complements. As for the bag vs bottle thing, I have owned this car since new and it came with the bag. I actually ordered it late in 1976 and it was built in March of 1977. Maybe it was an early build thing that got changed over later, or maybe they just ran out of bottles and used this to keep the line going? All I know is replacement bags are nonexistent but luckily mine is in good shape! If anybody out there has a good bag I would be interested in buying a spare!

bbobcat75

dale looks great!!! as far as the washer bottle/reservoir my 75 bobcat hatch back with factory 2.8 has a plastic one just like my 78 wagon with a 2.3 have a super nice one from a 80 if needed!!

take care and great work will be doing that to my 75 in about 20 years when it needs it and I need a project!!
1975 mercury bobcat 2.8 auto
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

dick1172762

Dale! Received the wire loom Friday. Looks great. Its got me all fired up to work on my Pinto (as soon as it warms up). Your car looks great. Its almost will be a shame to drive it (ALMOST). Keep up the good work. Sent you a letter today. Thanks again.~~~Dick
Its better to be a has-been, than a never was.

Alpine615

Loving the progress!  She looks beautiful - keep up the good work! :)
1980 Runabout

DBSS1234

Moving from front to back, the dash is in! For those of you with a black interior a perfect match for the factory semi flat black is SEM 39144 trim paint, it also comes in spray cans for those without a gun and an air compressor. The first picture is before the dash was installed and the second is after.........duh! ;)



Ignore the toy tractor sitting on the cowl, it is actually sitting on a saw horse in front of the car. I am restoring it for a friends new grandson.


dick1172762

Quote from: DBSS1234 on December 27, 2013, 01:13:51 PM
Engine bay is ready for the completed engine/transmission assembly. Hope to get the transmission back from the shop next week (had a little problem with the reassembly and called in the reinforcements). If anyone needs some of the wire loom covering I have plenty and will sell you enough to redo your car cheap. I had to buy the stuff in 100' rolls so I have alot left over. I have 3/4" ID, 1/2" ID and 1/4" ID but no extra clips or connectors as I reused my old ones. Let me know if interested.




How much a foot for 1/2 & 3/4 loom covering? Thanks
Its better to be a has-been, than a never was.

74 PintoWagon

Art
65 Falcon 2DR 200 IL6 with C4.

DBSS1234

I did it! I successfully stuffed 10 pounds of stuff into a 5 pound pail!! I got the transmission back Saturday and Sunday I installed the engine transmission assembly into the car.


Transmission bolted to engine.


Blankets padding the engine bay to avoid paint damage.


At this point I almost thought it was going to be impossible!


S-L-O-W-L-Y


It's in! ;D

DBSS1234

Was the washer reservoir bag an option on some models? My 77 sedan had the standard plastic washer reservoir.
[/quote]

I believe it was just the medthod they used with a V-6 in 1977. There isn't mush room with a V-6 and power steering in that area.

r4pinto

Wow you've done some really nice work!

Was the washer reservoir bag an option on some models? My 77 sedan had the standard plastic washer reservoir.
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress

74 PintoWagon

Art
65 Falcon 2DR 200 IL6 with C4.

Reeves1


Srt

Quote from: DBSS1234 on December 27, 2013, 01:13:51 PM
Engine bay is ready for the completed engine/transmission assembly. Hope to get the transmission back from the shop next week (had a little problem with the reassembly and called in the reinforcements). If anyone needs some of the wire loom covering I have plenty and will sell you enough to redo your car cheap. I had to buy the stuff in 100' rolls so I have alot left over. I have 3/4" ID, 1/2" ID and 1/4" ID but no extra clips or connectors as I reused my old ones. Let me know if interested.




Beautiful work there.

the only substitute for cubic inches is BOOST!!!

DBSS1234

Engine bay is ready for the completed engine/transmission assembly. Hope to get the transmission back from the shop next week (had a little problem with the reassembly and called in the reinforcements). If anyone needs some of the wire loom covering I have plenty and will sell you enough to redo your car cheap. I had to buy the stuff in 100' rolls so I have alot left over. I have 3/4" ID, 1/2" ID and 1/4" ID but no extra clips or connectors as I reused my old ones. Let me know if interested.




pinto_one

thanks but already got the engine done , done a few mods , took the 2.9 crank out of my wifes dead bronco II , machined the nose to take the gear (never liked chains) and installed it with a comp two cam, headers and TBI fuel injection ( see ranger site for the 2.8 conversion ) and a remote oil filter ( got tired of oil running down my arm every time I pulled the filter ) and last a A4LD automatic overdrive , get rid of the buzz at hwy speeds, but yours will look like a factory new car, nice
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

TIGGER

I must say you do very nice work.  This car is going to be amazing when it is done.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

DBSS1234

Quote from: pinto_one on December 05, 2013, 09:17:55 AM
very nice job there , doing my 76 V-6 right now ,  have a 79 V-6 Crusing wagon also that is on the waiting list, guess your going for the all orginal look with the smog pump and egr valve , and the valve cover stickers, I know that someone makes the 2.8 decal for the air cleaner top,  keep up the good work

If you need any engine parts let me know. To restore mine I scavenged 3 parts engines and have parts left over.

pinto_one

very nice job there , doing my 76 V-6 right now ,  have a 79 V-6 Crusing wagon also that is on the waiting list, guess your going for the all orginal look with the smog pump and egr valve , and the valve cover stickers, I know that someone makes the 2.8 decal for the air cleaner top,  keep up the good work
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

74 PintoWagon

Art
65 Falcon 2DR 200 IL6 with C4.

DBSS1234

Engine is finished, now if it runs half as good as it looks I should be in fine shape. ;)







Transmission is next!

:D

Scott Hamilton

Yellow 72, Runabout, 2000cc, 4Spd
Green 72, Runabout, 2000cc, 4Spd
White 73, Runabout, 2000cc, 4Spd
The Lemon, the Lime and the Coconut, :)

DBSS1234

Quote from: mrskydog on November 12, 2013, 10:27:44 AM
HATS OFF!! what a nice job on this car ,it will look better than new after you finish it. Wow  8)

That's the plan!  ;)

mrskydog

HATS OFF!! what a nice job on this car ,it will look better than new after you finish it. Wow  8)
"Living the Dream...Driving Old Fords"
1965 Mustang 2+2 Fastback
1980 Pinto Rallye 32,000 Org.
1972 Maverick Grabber V-8 car
2005 Mustang

DBSS1234

Axles installed and brakes done, almost a shame to cover it up with the drum. Next the motor! :)