Current Classifieds

72 Pinto parts
Date: 11/14/2019 10:46 pm
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
LOTS OF 1971-1973 PARTS FOR SALE
Date: 02/03/2018 11:28 am
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am
1979 PINTO PARTS--FREE
Date: 09/13/2022 02:05 pm
72 Pinto parts
Date: 12/04/2018 09:56 pm
1978 Pinto Wagon V8
Date: 04/28/2023 03:26 pm
Wheel cap
Date: 04/25/2022 11:21 pm
Mallory Unilight dist 2.0
Date: 10/25/2019 03:44 pm
1976 pinto for sale

Date: 01/12/2017 02:08 pm
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Crank Pulley Removal 2.3  (Read 516 times)

0 Members and 1 Guest are viewing this topic.

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 387
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Crank Pulley Removal 2.3
« on: October 02, 2022, 06:27:40 PM »
I searched the archives before posting, but I need advice for removing the crank pulley.  I put my 2-arm puller behind the inner groove and started to bend it so I stopped.  Would it be better to put the puller in between the two belt grooves?  Or is there a better way?  There doesn't seem to be a good way to spray penetrating oil so it gets onto the crank snout.  I've never had a hard time getting one off but this one has likely been on for a long time.  Any advice will be appreciated.
Logged
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 387
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #1 on: October 02, 2022, 07:31:49 PM »
I keep spraying penetrating oil and tapping but still not budging.  The crank pully bolt came out but the washer is still in there.  I haven't been able to get it out yet.  Do you think that is holding anything up?  I think it should still pop off.  I put my smaller three arm puller on and was able to grab the outer pulley and put some tension on it.  Maybe overnight while I'm sleeping the penetrating oil will work and it will pop off?  Wishful thinking...

What is the function of the two holes and notches in the snout of the pulley?  Is it for using some type of factory puller?
Logged
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 387
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #2 on: October 03, 2022, 07:21:32 PM »
SUCCESS!!!  A little heat from the MAP torch and it pulled off!  And I didn't have to get out the heave artillery (oxy-acetylene torch).  Next is to remove everything from the intake side of the engine.  I pray for no broken bolts...
Logged
rob289c
Pages: [1]   Go Up
« previous next »