Current Classifieds

Brake rotors
Date: 03/24/2017 09:02 pm
77 Wagon rear hatch
Date: 12/04/2019 05:57 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
oldskool787
Date: 02/12/2017 12:42 pm
73 rear hatchback glass
Date: 07/06/2017 11:33 am
Clutch pedal needed
Date: 01/11/2024 06:31 am
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
Oddsnends
Date: 12/20/2016 10:52 am
Deluxe Steering Wheel
Date: 10/16/2017 08:13 am

« previous next »
Pages: [1]   Go Down

Author Topic: cam choise  (Read 1348 times)

0 Members and 1 Guest are viewing this topic.

Offline Pup70

  • Pinto Member
  • **
  • Posts: 31
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
cam choise
« on: October 14, 2014, 04:23:19 PM »
I have a 2.3 that is punched 30 over head has been decked 80 thousands has a short ram ensliger intake 500cfm holley 2brrl and long tube header.  It has a cam in it now that is no good for the street i want something that had good bottom end power.  Any help would be great

Thanx Mike
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: cam choise
« Reply #1 on: October 14, 2014, 06:38:07 PM »
ATX or MTX? You got too much carb for bottom end. 350 better. When you start getting bottom end you may get pinging as well with that head cut. Too much squeeze unless you like running the most expensive gas. Look for cam with under 220 degrees intake at .050" lift. As much lift as you can get with that.
Logged

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2500
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: cam choise
« Reply #2 on: October 14, 2014, 07:46:08 PM »
I agree with AMC 49. And perhaps a cam with more overlap to bleed of some of the cylinder pressure.
Logged

Offline 78_starsky

  • Pinto Sr. Member
  • ****
  • Posts: 401
  • FeedBack: +21/-0
  • Forever Learning

    • Total Badges: 4
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary Windows User
Re: cam choise
« Reply #3 on: October 19, 2014, 11:11:09 AM »
hi,  this might help.

i have had 3 cams ground here and as long as your bump stick is in fair condition, this could save you money and get exactly what you need.

send geoff an email with what you are needing and what you have done to your motor.

check the profiles page and see if there is one there ready to go.

cheers

http://www.coltcams.com/

http://www.coltcams.com/html/camshaft/index.cfm
Logged
Pages: [1]   Go Up
« previous next »