Mini Classifieds

'80 Pinto Wagon
Date: 02/01/2018 05:20 pm
Wanted hood hinges
Date: 02/17/2020 05:30 pm
WTB. Seat cover or material LFront
Date: 07/01/2019 03:17 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
Modine 427 Pinto Bobcat V6 Radiator appears new

Date: 09/17/2024 12:35 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 1,292
  • Online ever: 2,670 (May 09, 2025, 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 502
  • Total: 502
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

Window channel installation

Started by FlyerPinto, January 02, 2013, 10:55:21 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

78txpony

The rivets holding the little metal window guides were a factory thing - less time for installation. 
When I replaced my channels with the tops-down channels, I just used some adhesive there and they have held up fine. 
-Rob Young
1978 Pinto Pony sedan (Old Faithful) a.k.a. "the Tramp"
http://www.flickr.com/photos/thelonerider2005/sets
1972 Cutlass Supreme Convertible (442 clone) -"Lady" (My mistress...)
http://www.flickr.com/photos/robsalbum/sets
1986 Cutlass Supreme Coupe - "Pristine"
1997 H-D Sportster

Pinto5.0

There is a difference in the thickness of door glass between the years but it shouldn't affect anything. I'm pretty sure '71 to '76 are thicker than '77 & up. I think I read that someplace 7 or 8 years ago so if anyone can correct me on the exact years, feel free.
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

flash041

It does not come with the clip, I reused the old one.And yes I used the 71-76. Fit perfectly in my 78.
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

bbobcat75

does the widow channel rubber you got have the metal tab that is in the curve, or do you use your old ones??  the metal tab i am talking about is the anti-rattle i think  not too sure what it is called.

thanks
1975 mercury bobcat 2.8 auto
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

HOSS429

Quote from: flash041 on January 06, 2013, 09:38:59 AM
I replaced mine last year with channel I bought from Auto Krafters.It fit perfectly in my 78 , even though their listing was for earlier years..
they advertise one for 71 thru 76 models .. is this the one you used ?  .. ok i need one for my 73 and my 80 so i just ordered one for my 73 and will try it in my 80 and let folks know .....

flash041

I replaced mine last year with channel I bought from Auto Krafters.It fit perfectly in my 78 , even though their listing was for earlier years.The Auto Krafter ones are of a heavier material that the ebay ones. I dont recall any rivets holding it in other that the rivet holding the clip to the seal. When I installed the clip I did not rivet it, just slipped it over the seal and pressed it into the channel.I used no adhiesive at all and so far it has not moved.
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

FlyerPinto

The rivet holding the clip in would make sense. Not quite sure if I'll need to rivet through the new channel as they did, or if I can do the rivet first and then set the channel on top of it. I haven't gotten back out to do any work, it's colder than old Billy out there...I did post the phone number for the convertible folks also, in case the ebay thing ends up not being what anyone needed. I bought my door seals and station wagon hatch seal from Steele Rubber. They are perfect. I haven't done the hatch for the Bobcat yet, and to be honest I don't know if Steele has that part or not, but they will be my first option.
1977 Bobcat HB
1977 Bobcat HB
1978 Pinto Cruising Wagon

So many projects, so little time...

Pinturbo75

75 turbo pinto trunk, megasquirt2, 133lb injectors, bv head, precision 6265 turbo, 3" exhaust,bobs log, 8.8, t5,, subframe connectors, 65 mm tb, frontmount ic, traction bars, 255 lph walbro,
73 turbo pinto panel wagon, ms1, 85 lb inj, fmic, holset hy35, 3" exhaust, msd, bov,

HOSS429

Quote from: Pinto5.0 on January 02, 2013, 07:22:44 PM
I got the channel, door seals & squeegees from them though I didn't install them yet. They appear to be a great match to the dry originals.

do you have contact info .. i cant find them on ebay ,,   

Pinto5.0

I got the channel, door seals & squeegees from them though I didn't install them yet. They appear to be a great match to the dry originals.

I think that rivet secures the anti-rattle clip to the rubber window channel if I'm not mistaken.
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

FlyerPinto

The company was Convertible Top Specialists on Ebay. The item was described as door glass window channel and they list several vehicles compatible with this item, including all Pintos from 1974 to 1980 and Mercury Bobcats from 1975 to 1980. There is an illustration of the item, and it lists for $29 for an eight foot roll. Part of the description reads "The window channel is the material that goes in the frame around the door windows, the channel holds the window in place so it doesn't rattle around. We also have Pinto door seals, window sweeps, cowl seals & wagon hatch seals in stock." Their phone number is 800-272-2394. I didn't have any problem with these folks at all, in fact they worked with me to fix my screwup when I inadvertently used an inactive account to pay for the items. The two lengths I received came via US Mail and were packaged nicely. I wouldn't hesitate to recommend them.
1977 Bobcat HB
1977 Bobcat HB
1978 Pinto Cruising Wagon

So many projects, so little time...

FlyerPinto

Sure thing, I'll post it this evening when I get home. If I can dig out the invoice aspect I'll get the part number and all that good stuff.
1977 Bobcat HB
1977 Bobcat HB
1978 Pinto Cruising Wagon

So many projects, so little time...

HOSS429

post where you got the channels from if you can cause i need them for both my pintos ..

FlyerPinto

Hey all,

I was pulling the old window channel out of the window frame in the Cruising Wagon yesterday and encountered something I wasn't certain about. This is the felt and rubber piece that fits inside the window frame that the window rolls up into. I bought new ones from a company in Florida (Convertible Tops I believe) and the issue isn't with the new parts, it's more of a question about the old. I was pulling the old one out of the driver's door; it was very brittle and retained none of the flexibility from when it was new, so it is kind of a pain to get out. However, as I was looking at the underside of the window channel I saw what appears to be a rivet in the channel. It is located by the curvature of the window frame and very near the window guide clips. I'm not sure why it would have been necessary, since regular adhesive should be more than enough to hold this material in place. I should have checked the other door or even the Bobcat to see if it had the same rivet; if it does then I can assume it is a factory thing. But I didn't think to do that just then, and before I go back at it I wanted to see if anyone had encountered this before, and if it is in fact a factory rivet or just something some jamoke did to the car. I'll check the other doors tonight and post what I find, but I'd love to hear from folks on this one. Thanks,

Matthew
FlyerPinto
1977 Bobcat HB
1977 Bobcat HB
1978 Pinto Cruising Wagon

So many projects, so little time...