Current Classifieds

Looking for a few parts - TIA
Date: 02/19/2023 12:18 pm
A.c. alternator hrackets
Date: 09/03/2017 12:11 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
Need a 1976 runabout instrument cluster replacement
Date: 12/26/2016 04:29 pm
Accelerator Pump Diaphram for 1978 Pinto
Date: 09/03/2018 08:58 am
Need hatchback fuel tank sending unit
Date: 08/13/2018 02:46 pm
need intake for oval port 2.3l
Date: 08/22/2018 09:23 am

« previous next »
Pages: [1]   Go Down

Author Topic: what socket for 2.3 head bolts  (Read 1700 times)

0 Members and 1 Guest are viewing this topic.

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
what socket for 2.3 head bolts
« on: July 14, 2013, 12:52:07 PM »
Hello all, I am trying to remove my head bolts from my 2.3L ('76) and wasn't sure what size the bolts are.  They look like 1/2" 12 point socket, but I am not sure.  I also read on here that these can be reused?  Any clarifications would be helpful!  Thanks!
Logged

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: what socket for 2.3 head bolts
« Reply #1 on: July 14, 2013, 03:45:10 PM »
It is a 12 point but either 1/2" or 9/16". They are re-usable & I'm hearing preferred over ARP studs which are supposedly lacking enough threads on the block side.   
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #2 on: July 14, 2013, 04:29:58 PM »
All the engine fasteners are metric... try 13mm.
Logged
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #3 on: July 14, 2013, 04:40:01 PM »
Thanks for the info, I did try the 9/16 and it was just slightly too big.  I'll have to check on the metric too, so thanks for the tip!
Logged

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: what socket for 2.3 head bolts
« Reply #4 on: July 14, 2013, 05:57:20 PM »
OK, wasn't sure. 1/2" & 13mm are interchangeabl e but use the one with the tightest grip. 13mm is a human hair smaller than 1/2" & only the best quality tools are that accurate.
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #5 on: July 14, 2013, 06:24:34 PM »
Awesome, ordered a 13mm socket.  Hopefully it'll be here soon.  Very excited to get these old heads off and over to bo-port to get some work done on them. 
Logged
Pages: [1]   Go Up
« previous next »