Current Classifieds

1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
1974 Ford Pinto

Date: 10/16/2017 10:45 am
78-80 Windshield
Date: 10/29/2021 03:11 pm
Need 76' coupe rear Glass and Front Grille
Date: 07/20/2017 01:23 am
1973 Pangra

Date: 01/06/2015 02:19 pm
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Lower Alternator bracket
Date: 08/26/2017 05:11 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Vinegar for galvanized removal  (Read 722 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Vinegar for galvanized removal
« on: November 18, 2019, 11:31:54 AM »
Hi all..

As I mentioned in another post here I am redesigning the custom manifold I built awhile back to fit 2 SU sidedrafts to my 2.0 and am planning to use some 1 1/4 galvanized EMT conduit for runners.

Since its not advisable to weld galvanized i want to remove the zinc.

I have  been reading that vinegar can be used to etch off the zinc..

Has anyone had experience with this
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2501
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Vinegar for galvanized removal
« Reply #1 on: November 18, 2019, 11:40:43 AM »
If not vinegar then likely phosphoric acid. But, even there you will have to likely lightly sand the surfaces if it works. Recently working on my Corvair I have used the washing soda and a sacrificial steel piece to transfer rust. I'm wondering if you could do the same to remove the galvanization???
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Vinegar for galvanized removal
« Reply #2 on: November 18, 2019, 11:46:31 AM »
I was thinking of using concentrated vinegar and adding some table salt to make hydrochloric  acid to speed up the process and maybe warming the solution a bit and placing it in the sun to keep it warm.

Ill give it a try and report back.
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline JoeBob

  • Pinto Sr. Member
  • ****
  • Posts: 536
  • FeedBack: +51/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Photographer Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Vinegar for galvanized removal
« Reply #3 on: November 18, 2019, 02:42:33 PM »
If you see white powder on your weld there is still zinc present.   
Logged
77 yellow Bobcat hatchback
Deuteronomy 7:9

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2501
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Vinegar for galvanized removal
« Reply #4 on: November 19, 2019, 11:40:10 AM »
And, isn't it interesting that the "Weld Thru Primers" as far as I know contain zinc. Go figure.
Logged
Pages: [1]   Go Up
« previous next »