Current Classifieds

looking for parts
Date: 06/19/2020 02:32 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
1973 Bobcat Cruzin Wagon for Sale $4000 obo

Date: 04/13/2018 11:30 am
looking for parts
Date: 06/19/2020 02:32 pm
2.3 front sump oil pan
Date: 02/19/2017 03:24 pm
Looking for leaf spring insulators
Date: 04/04/2020 09:38 am
WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am
Dumping '80 yellow Pinto

Date: 06/21/2017 03:45 pm
 (3) 1980 Ford Pinto Station Wagon Projects

Date: 03/15/2023 02:16 pm
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
Ford 2.3L new gaskets for sale
Date: 12/10/2016 04:11 pm
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm

« previous next »
Pages: [1]   Go Down

Author Topic: lifter removal  (Read 2031 times)

0 Members and 1 Guest are viewing this topic.

Offline lostandfound

  • Pinto Member
  • **
  • Posts: 66
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Fifth year Anniversary
lifter removal
« on: December 20, 2005, 02:25:22 AM »
i have removed the camshaft and all of the parts on the cylinder head but the lifters will not budge i can lift the cylinder head up  by picking it up by  the lifter
Logged
1979 2.3l sedan wooohooo

Offline johnsonracing

  • Pinto Member
  • **
  • Posts: 59
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Tenth year Anniversary Fifth year Anniversary
Re: lifter removal
« Reply #1 on: December 20, 2005, 07:04:36 AM »
using a visegrip clamped on the lifter,( down from the top pivot area to prevent damage)tap on the bottom of visegrip with hammer to force the lifter up and out.You should buy a new set if you are doing any motor freshening.Che ap,should be able to get a set for under $40.00 at the right auto parts store.
   If you are putting in a new cam you have to buy new cam followers.This a must because the two parts have to wear-in together.
 :o :o
Logged

Offline 77turbopinto

  • PCCA VIP
  • Pinto Sr. Master
  • ***
  • Posts: 2762
  • FeedBack: +99/-0
  • No good deed goes unpunished…..

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary 1000 Posts Fifth year Anniversary
Re: lifter removal
« Reply #2 on: December 20, 2005, 09:18:09 AM »
The easy way that I do it is with a grease gun. Use a pointed fitting and inject grease into the holes next to each lifter. They will pop right out. Remove the grease and install new lifters. I have had some that you could lift the car with(broke apart with the vise-grip), but they just slide out with the grease, amazing.

Bill
Logged
Thanks to all U.S. Military members past & present.
Pages: [1]   Go Up
« previous next »