Current Classifieds

1980 Ford Pinto Squire Wagon * All original 1 Owner *

Date: 09/15/2019 12:28 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
1971 Pinto instrument cluster clear bezel WTB
Date: 03/16/2017 10:00 pm
front end parts
Date: 03/30/2018 12:48 pm
Clutch Cable Needed
Date: 04/03/2017 11:03 pm
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
1972 Rallye wagon rebuild
Date: 11/14/2020 07:31 pm
Built 2.0
Date: 10/07/2018 05:27 pm
1973 Pangra gauge and tach panel

Date: 11/02/2019 10:25 am
Need 77 or 78 Cruising Wagon Speedometer Tachometer Assembly
Date: 06/24/2020 06:12 am
Plug Or Cover For Hatch Hinge Bolt For 1979
Date: 05/28/2017 03:20 pm
Deluxe Steering Wheel
Date: 10/16/2017 08:13 am

Author Topic: I have a D-port intake question.  (Read 1557 times)

0 Members and 1 Guest are viewing this topic.

Offline richcon76

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • The American Mini

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
I have a D-port intake question.
« on: December 18, 2012, 10:02:34 PM »
I am running a D-port head and was woundering which intake would be better to run? One intake that I have is the early D-port (the one that a two barrel bolts to) and the other one I have is the EFI intake. I will be running a 350cfm Holley and want to know what flows better.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: I have a D-port intake question.
« Reply #1 on: December 19, 2012, 01:52:44 AM »
If the carb will clear your hood, the EFI is MUCH better. Much better!!!!
Its better to be a has-been, than a never was.

Offline racer99

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +4/-0
  • Gender: Male
  • Just damn junk with a bt carb

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User Mobile User Windows User
Re: I have a D-port intake question.
« Reply #2 on: December 19, 2012, 06:34:41 AM »
The 4 square EFI lower and an adapter works good.
I use the same intake, knife-edged with a 1 inch 4bbl spacer
tigged to it.

Offline richcon76

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • The American Mini

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: I have a D-port intake question.
« Reply #3 on: December 19, 2012, 09:24:20 AM »
Thanks racer99 and dick1172762! I thought the efi was better, but wanted to find out. I will just put the early D-port on the shelf.

Thanks, again