Current Classifieds

sport steering wheeel
Date: 10/01/2020 10:58 pm
Instrument Panel with Tach wanted
Date: 05/15/2022 11:36 am
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
Pinto Vinyl Top

Date: 10/09/2020 10:29 pm
windshield
Date: 04/14/2018 08:53 pm
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
79 pinto driveshaft
Date: 08/18/2018 02:03 pm
pinto floor mats??

Date: 01/11/2017 07:27 am

« previous next »
Pages: [1]   Go Down

Author Topic: Help with engine identification  (Read 14309 times)

0 Members and 1 Guest are viewing this topic.

Offline sundug

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Help with engine identification
« on: November 18, 2023, 10:30:34 AM »
I was given a Blakely Bearcat kit car that has Pinto running gear. Unfortunately I do not have the original VIN and there are no tags on the engine or transmission. It is an inline four of unknown vintage and that's where I need help. How can I tell the difference between the 2L and the 2.3L engine without any tags? I have the same problem with the three speed automatic transmission. I'm pretty sure it's an early C4, as the dipstick tube does not go into the pan. Any help would be greatly appreciated. I can provide pictures. Thanks, Doug
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Help with engine identification
« Reply #1 on: November 18, 2023, 02:49:42 PM »

There is the early 2.0 OHC engine used through 1974 that was built in Germany and is referred to as the EAO engine. Otherwise there is the USA 2.3 Lima OHC engine that was used from 74-thru the end run in 1980. There was also an early push rod 1.6 Kent engine and the V-6 Engine but yours is obviously not either of those. Also worth mentioning there was a 2.0 (and a 2.5) Lima engine used in the Ranger trucks. So, be aware that the 2.0 EAO German and the USA Lima 2.0 engines are not the same.

I promptly removed my 2.0 EAO engine from my '73 Pinto and swapped in a Turbo 2.3 Lima engine from my fuel injected '88 T-Bird Turbo Coupe. Thus I'm not the best to tell the difference. That said, I have provided two pictures of my 2.0 EAO. There are aspects I believe are different between the 2.0 EAO and the 2.3 Lima engine that to the untrained eye look similar. Of note is the smallish distributor cap, the fuel pump that mounts with top/bottom bolts and the front pulley and timing "window" on the 2.0 EAO engine. I also notice a "20" on the lower part of the timing cover. I'm not sure if that denotes the 2.0 (EAO) engine or not??? I hope these help.
Logged
Pages: [1]   Go Up
« previous next »