Current Classifieds

74 hood
Date: 07/03/2017 03:46 pm
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm
Oil pan front sump style
Date: 01/10/2017 09:19 am
4:11 gears for 6.75 Make offer...NEED GONE

Date: 08/01/2018 01:27 pm
Various parts for 1980 Pony (good to N.O.S. condition
Date: 06/07/2018 01:45 am
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
1977 Pinto Hatchback Parts

Date: 08/29/2020 05:31 pm
74 pinto
Date: 09/11/2016 06:32 pm
Squire trim
Date: 03/28/2018 10:11 am
Various Pinto stuff for sale.
Date: 11/21/2018 01:56 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm

Author Topic: Crank Pulley Removal 2.3  (Read 474 times)

0 Members and 1 Guest are viewing this topic.

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Crank Pulley Removal 2.3
« on: October 02, 2022, 06:27:40 PM »
I searched the archives before posting, but I need advice for removing the crank pulley.  I put my 2-arm puller behind the inner groove and started to bend it so I stopped.  Would it be better to put the puller in between the two belt grooves?  Or is there a better way?  There doesn't seem to be a good way to spray penetrating oil so it gets onto the crank snout.  I've never had a hard time getting one off but this one has likely been on for a long time.  Any advice will be appreciated.
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #1 on: October 02, 2022, 07:31:49 PM »
I keep spraying penetrating oil and tapping but still not budging.  The crank pully bolt came out but the washer is still in there.  I haven't been able to get it out yet.  Do you think that is holding anything up?  I think it should still pop off.  I put my smaller three arm puller on and was able to grab the outer pulley and put some tension on it.  Maybe overnight while I'm sleeping the penetrating oil will work and it will pop off?  Wishful thinking...

What is the function of the two holes and notches in the snout of the pulley?  Is it for using some type of factory puller?
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #2 on: October 03, 2022, 07:21:32 PM »
SUCCESS!!!  A little heat from the MAP torch and it pulled off!  And I didn't have to get out the heave artillery (oxy-acetylene torch).  Next is to remove everything from the intake side of the engine.  I pray for no broken bolts...
rob289c