Current Classifieds

1974 Ford Pinto

Date: 10/16/2017 10:45 am
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
Looking for a 1977 Ford Pinto Runabout Hatchback
Date: 10/15/2017 10:03 am
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
Pinto Runabout wanted
Date: 06/05/2018 04:42 pm
1973 Pinto 2.3 4 speed transmission. Tube frame roadster frame (roller). 1971 Pinto 2.0 radiator.
Date: 09/05/2018 06:30 pm
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
parts needed
Date: 02/20/2017 07:58 am
1975 Pinto bumpers
Date: 10/24/2019 01:43 pm
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm
SVO SWAP
Date: 03/15/2018 03:12 am

« previous next »
Pages: [1]   Go Down

Author Topic: Crank Pulley Removal 2.3  (Read 475 times)

0 Members and 1 Guest are viewing this topic.

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Crank Pulley Removal 2.3
« on: October 02, 2022, 06:27:40 PM »
I searched the archives before posting, but I need advice for removing the crank pulley.  I put my 2-arm puller behind the inner groove and started to bend it so I stopped.  Would it be better to put the puller in between the two belt grooves?  Or is there a better way?  There doesn't seem to be a good way to spray penetrating oil so it gets onto the crank snout.  I've never had a hard time getting one off but this one has likely been on for a long time.  Any advice will be appreciated.
Logged
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #1 on: October 02, 2022, 07:31:49 PM »
I keep spraying penetrating oil and tapping but still not budging.  The crank pully bolt came out but the washer is still in there.  I haven't been able to get it out yet.  Do you think that is holding anything up?  I think it should still pop off.  I put my smaller three arm puller on and was able to grab the outer pulley and put some tension on it.  Maybe overnight while I'm sleeping the penetrating oil will work and it will pop off?  Wishful thinking...

What is the function of the two holes and notches in the snout of the pulley?  Is it for using some type of factory puller?
Logged
rob289c

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank Pulley Removal 2.3
« Reply #2 on: October 03, 2022, 07:21:32 PM »
SUCCESS!!!  A little heat from the MAP torch and it pulled off!  And I didn't have to get out the heave artillery (oxy-acetylene torch).  Next is to remove everything from the intake side of the engine.  I pray for no broken bolts...
Logged
rob289c
Pages: [1]   Go Up
« previous next »