Current Classifieds

1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
Wagon rear quarters
Date: 06/17/2020 03:32 pm
Oddsnends
Date: 12/20/2016 10:52 am
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
1974 Pinto Inside Rear View Mirror & Brake Pedal Pad

Date: 02/18/2017 04:41 pm
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
Automatic Wagon
Date: 06/14/2019 11:22 pm
Pinto Runabout wanted
Date: 06/05/2018 04:42 pm
72' hatchback parts wanted
Date: 08/25/2019 02:57 am
Steering Wheel Needed for 1972 Pinto
Date: 08/08/2018 12:26 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Crank pulley and outer timing cover Help  (Read 1236 times)

0 Members and 1 Guest are viewing this topic.

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Crank pulley and outer timing cover Help
« on: April 19, 2023, 01:13:42 PM »
Finally found a junk yard with a couple Pintos. One of which was a 2.3 with the outer timing cover still there. That’s what I needed. Pulled the bolts and….discovered that you need to pull the crank pulley to remove said cover.  70 mile round trip. :-\  So, two questions:

Is it true you need to pull crank pulley to get the outer cover off?

How hard are these pulleys to remove?  Been sitting there for a loooong time. Spray lube, impact, pry bars, three jaw puller?  Any tips or advice appreciated!

Thanks.
Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 108
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: Crank pulley and outer timing cover Help
« Reply #1 on: April 19, 2023, 06:41:57 PM »
I 'VE NEVER HAD TO REMOVE PULLEY TO GET THE COVER OFF.YOU HAVE TO FENAGLE IT A LITTLE TO FIND THE SWEET SPOT AROUND BRACKETS .PULLEY IS NOT PRESSED ON .
Logged
D BARHAM

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #2 on: April 22, 2023, 07:13:49 PM »
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run. 
Logged
rob289c

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Crank pulley and outer timing cover Help
« Reply #3 on: April 22, 2023, 10:14:46 PM »
Quote from: rob289c on April 22, 2023, 07:13:49 PM
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run.

Think a regular propane torch would work?  Don’t have a Mapp one and I’m not gonna even try to haul the oxy / acetylene rig down there.
Logged

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 381
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #4 on: April 24, 2023, 07:30:50 PM »
I'm not sure if the propane torch would be hot enough.  The pulley has been on the snout for over 40 years so it might take a bit to free it up.  If that's all I had, I would give it a try. 
Logged
rob289c
Pages: [1]   Go Up
« previous next »