Current Classifieds

71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
1971-1975 Pinto
Date: 01/09/2017 04:14 pm
6.6.75 carrier
Date: 02/14/2018 06:47 am
1980 Pinto Wagon

Date: 02/29/2020 07:01 pm
Wanted Postal Pinto
Date: 09/26/2019 05:31 pm
Clutch Cable Needed
Date: 04/03/2017 10:54 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
1979 hatch needed
Date: 05/13/2018 08:52 pm
1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
72 Pinto parts
Date: 11/14/2019 10:46 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am

« previous next »
Pages: [1]   Go Down

Author Topic: Coils Prings  (Read 604 times)

0 Members and 1 Guest are viewing this topic.

Offline mklarose

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Male
  • Nova Scotia Pinto

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Coils Prings
« on: October 04, 2020, 07:37:06 PM »
Will coil springs from a 74 or later version fit my 71, 2 lt sedan?
If so will the coils need to be cut and how many?
If later versions do not work well, are there any other models that can be made to fit with good ride height and comfort?

Any thoughts?

Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Coils Prings
« Reply #1 on: October 05, 2020, 04:02:29 AM »
The later 74 up springs are too long in length and would need shorting.  If nobody here provides input, trial and error cutting coils off a 74 up spring could be done.  Also suggest contacting RacerWalsh.com as they advertise coil springs for the 71 with various spring rates.
Logged
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Coils Prings
« Reply #2 on: October 05, 2020, 11:57:50 AM »
One of the things about cutting springs is that it stiffens the rate. There are spring calculators that might be helpful to determine how much.  As it is '74 and up springs are probably rate higher because of the 2.3 engine. I don't know the cost (probably not cheap) but I believe you can have springs wound to specification.

  Somewhere (I think it was MOOG) has a chart showing all the wire diameters, coil count, coil circle diameter and free length. It might be by that process you can find a spring "close enough" for another application that can be used. Just as an example a lot of Studebaker guys use aftermarket "Cargo Carrier," variable rate, mid-80's GM FWD, REAR springs - on the FRONT of their cars. This was ultimately determined by using a spring chart and doing a comparison.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: Coils Prings
« Reply #3 on: October 06, 2020, 08:37:22 PM »
What's wrong with the springs you have?
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.
Pages: [1]   Go Up
« previous next »