Current Classifieds

WANTED: Skinny Rear Bumper w/o guards for '71 or '72 Pinto Coupe
Date: 04/24/2018 11:45 am
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm
Weber dcoe intake 2.0

Date: 08/01/2018 01:09 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
Parts Parts Parts
Date: 09/08/2018 03:13 pm
95 2.3l short block
Date: 03/18/2017 04:54 pm

« previous next »
Pages: [1]   Go Down

Author Topic: aftermarket tach  (Read 1507 times)

0 Members and 1 Guest are viewing this topic.

Offline ERusinko

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Tenth year Anniversary Fifth year Anniversary
aftermarket tach
« on: April 30, 2023, 10:38:07 PM »
I've tried 2 different tachs and when i hook them up they both peg at 10,000 while the car is at an idle !
I'm conected to a switched power (Red), tried 2 different grounds (Black), and hooked to the negative side of the coil (Green).
Is there something different with electronic ignition ?
1978 Pinto 2.3 litre
I could appreciate any help !!
Eddie Rusinko
Yuma, AZ
Logged

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2500
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: aftermarket tach
« Reply #1 on: May 01, 2023, 12:01:06 PM »
Is it possible someone reversed the factory wires at the coil? I'd remove both wires and test for voltage at each with the ignition on. I'd assume that the electronic ignition still triggers the coil by switching the ground on and off like a points distributor. Otherwise from your description it sounds like it is wired right.
Logged

Offline PintoTim2

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • '72 Pinto & '80 Pinto Pickup

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Topic Starter Mobile User
Re: aftermarket tach
« Reply #2 on: May 01, 2023, 05:07:46 PM »
Any chance the ignition module is doing multispark?   
Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 108
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: aftermarket tach
« Reply #3 on: May 01, 2023, 06:51:07 PM »
AFTER MARKET TACHS HAVE A SWITCH FOR 4,6 OR 8 CYL.SOME ARE ON THE INSIDE OF IT,WOULD NOT READ RIGHT IF NOT SET  FOR 4 CYL.
Logged
D BARHAM

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2500
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: aftermarket tach
« Reply #4 on: May 02, 2023, 11:48:36 AM »
Quote from: davidpinto on May 01, 2023, 06:51:07 PM
AFTER MARKET TACHS HAVE A SWITCH FOR 4,6 OR 8 CYL.SOME ARE ON THE INSIDE OF IT,WOULD NOT READ RIGHT IF NOT SET  FOR 4 CYL.

That is a good point that I forgot to consider. However, I believe if it was set to 8 (or 6) cylinders that it would read lower, not higher. And even if it is the other way around it would only double and a 900-ish RPM idle would be 1,800 RPM, but he is pegging at 10,000 RPM. So, while he may not have it set in the right position (and should make that correction as you note) the 10,000 RPM idle likely has another cause.
Logged
Pages: [1]   Go Up
« previous next »