Current Classifieds

1978 bobcat 4speed shifter
Date: 11/02/2023 09:51 pm
1600 CC WATER PUMP
Date: 06/02/2018 09:13 am
Need 72 pinto parts!
Date: 06/14/2019 01:40 pm
1976 pinto for sale

Date: 01/12/2017 02:08 pm
1972 Pinto for sale

Date: 05/19/2021 12:41 am
1977 Pinto Cruizin Wagon

Date: 04/11/2024 03:56 pm
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
Squire trim
Date: 03/28/2018 10:11 am
hubcaps

Date: 05/13/2021 05:33 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
77 Caliper Bolt
Date: 08/21/2018 04:02 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 2.0 auto to stick shift  (Read 2852 times)

0 Members and 1 Guest are viewing this topic.

Offline 1931ford

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
2.0 auto to stick shift
« on: November 04, 2009, 03:59:22 PM »
I have put a 2.0 with a c4 automatic in a 31 Ford .I would like to put a 5 speed stick in the 31, will a trans from a 1980's 2.3 Mustang fit? All the Pintos Capris & Mustang IIs are long gone in the local junk yards .  will I need to have the crankshaft machined for a pilot bushing .Thanks for any help 
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: 2.0 auto to stick shift
« Reply #1 on: November 05, 2009, 08:13:44 AM »
I have not done this swap so my info is suspect.  The car 5 speeds have the shifter located towards the rear of the transmission tailhousing.  From what the magazines show, you might need the shifter farther forward in your 31.  The Ranger 2.3 5 speeds seem to locate the shifter farther forward but I think they are not T5's.  TurboPinto72 has a thread showing how he added a 2.3 T5 to his 2.0 Pinto.
http://www.fordpinto.com/index.php/topic,33.20.html
Since you have an auto, you need a stock 2.0 pilot bearing.  The car 2.0 and 2.3 manual transmission pilot shafts are the same diameter (or as close as I can measure).  Note that the car 5.0 T5 has a larger pilot shaft.  This link shows some of the T5 dimensions and available gear ratios.
http://www.allfordmustangs.com/Detailed/349.shtml
The 2.3 FOX chassis cars came with several different types of clutch cable pull type T5 bellhousings.  The 87 & 88 turbocoupe came with a hydraulic actuated clutch T5 bellhousing.  The 2.0 and 2.3 bellhousing to engine block locating dowels are different sizes and these step dowels may help.
http://www.turboford.net/ubb/ultimatebb.php?ubb=get_topic;f=6;t=013741
I am not familiar with what flywheel clutch set up that works best.  Hopefully somebody will add or the search function should find additional.
Logged
Jerry J - Jupiter, Florida
Pages: [1]   Go Up
« previous next »