Current Classifieds

4-14" Chrome Plated Wheels 4 x 108 + 0mm offset with new tires

Date: 09/12/2018 12:33 pm
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
2 liter blocks and heads
Date: 03/28/2018 09:58 am
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:41 am
Instrument Panel with Tach wanted
Date: 05/15/2022 11:36 am
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
Intake, Head, and valve cover gasket sets

Date: 12/10/2017 01:14 pm
Front sway bar

Date: 07/23/2018 08:19 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 1972 california only timing mark  (Read 1385 times)

0 Members and 1 Guest are viewing this topic.

Offline Sir Thomas Crapper

  • Pinto Member
  • **
  • Posts: 23
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
1972 california only timing mark
« on: September 16, 2014, 01:34:35 PM »
My 2.0 Squire has a notch in the crank pulley that timing is set to.  No degree marks at all. 

Does anyone know what the notch is, as far as how much advance does it get me, and where should i realistically set it?

The engine I installed has a custom ground  crane cam.  I don't want to go crazy with it, as it needs to run a 14 1/2 hour race.  and there's a leaf blower supercharger on it with -20 windshield washer fluid being sprayed into the carb.  other than that, it's pretty much stock.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: 1972 california only timing mark
« Reply #1 on: September 16, 2014, 04:44:36 PM »
Motor manual back in the day shows a degreed balancer for 71-72 2.0. 6 BTDC on ATX and 9 BTDC for California. Sure you don't have other marks? They are usually faint and the notch is much more prominent. Often covered by paint or rust.
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: 1972 california only timing mark
« Reply #2 on: September 16, 2014, 09:54:44 PM »
My balancer is degreed but you can barely see the numbers even after I cleaned it, smeared whiteout over the area and wiped it off real quick and the numbers showed right up, might want to try that..
Logged
Art
65 Falcon 2DR 200 IL6 with C4.
Pages: [1]   Go Up
« previous next »