Current Classifieds

1978 PINTO PONY FOR SALE 17,000 ORIGINAL MILES !!!!!!!
Date: 10/10/2019 09:42 pm
71-73 sway bar
Date: 06/12/2021 10:12 am
Need 77 or 78 Cruising Wagon Speedometer Tachometer Assembly
Date: 06/24/2020 06:12 am
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
Wanted - Offenhauser intake for 2.8l (6097DP)
Date: 01/28/2019 05:15 pm
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
1979 Pinto 3-door Runabout *PRICE REDUCED*

Date: 08/01/2023 06:53 pm
Wanted hood hinges
Date: 02/17/2020 05:30 pm
WTB 1974 or 1975 Pinto Grille and Turn Signals
Date: 04/08/2018 05:47 pm
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am
74 Pinto Hub Caps & Trim Rings

Date: 02/18/2017 04:47 pm

« previous next »
Pages: [1]   Go Down

Author Topic: neoprene gasket & glue?  (Read 1460 times)

0 Members and 1 Guest are viewing this topic.

Offline 79copperwagon

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
neoprene gasket & glue?
« on: April 17, 2017, 06:38:26 PM »

Anybody out there know the best glue or tack to use with a neoprene vc gasket for a 79 wagon with 2300?
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: neoprene gasket & glue?
« Reply #1 on: April 18, 2017, 07:42:42 AM »
If its a blue Felpro, no glue is necessary. The gasket is a life time rated one.
Logged
Its better to be a has-been, than a never was.

Offline 79copperwagon

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: neoprene gasket & glue?
« Reply #2 on: April 18, 2017, 01:30:58 PM »
It isn't- its a thick black Mahle-I was told by the one parts guy I should use Permatex Ultra Black & another guy wanted to sell me RTV- This is my 1st use of non-cork & its a 1 piece - if you know the engine it has that arch in the front for the timing belt so i'm having trouble keeping it in place-so any help appreciated ;)
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: neoprene gasket & glue?
« Reply #3 on: April 20, 2017, 05:15:36 PM »
Most of the rubber valve cover gaskets that I recall (similar to the 2.3 engine) typically call for a sealant at the front, inner corners where it sweeps upward over the arch. In the past I have always used RTV. Love to buy the smaller tubes at the 99 Cent only stores so I don't wind up throwing 80% of it away when it eventually hardens in the larger tube.
Logged
Pages: [1]   Go Up
« previous next »