Current Classifieds

1974 Wiring diagram free
Date: 10/27/2019 06:56 pm
1974 Pinto Right Rear Interior Trim Panel

Date: 02/18/2017 04:44 pm
hubcaps

Date: 06/05/2018 09:13 pm
Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
 1979 Ford Pinto for Sale - price reduction

Date: 01/23/2023 02:22 pm
Intake manifolds

Date: 03/06/2021 03:04 pm
Rare parts for sale
Date: 09/10/2018 08:38 am
1973 Ford Pinto Squire Wagon 3 Door

Date: 07/11/2023 11:39 pm
Parting out 77 Bobcat Hatch
Date: 11/06/2017 04:16 pm
WTB: 2.0 Mech tach drive distributor
Date: 04/14/2023 06:15 am
Intake manifolds

Date: 03/06/2021 03:04 pm
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Another V8 conversion question  (Read 1152 times)

0 Members and 1 Guest are viewing this topic.

Offline jharmke

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +0/-0
  • Gender: Male
  • 77 Pinto Wagon in NJ

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User
Another V8 conversion question
« on: March 09, 2016, 08:58:30 AM »
I have seen a bunch of posts regarding V8 conversions. However, I think I hit a snag as I am converting a V6 and I think the V6 frame mounts (NOT MOTOR MOUNTS) are different from the 4 cylinder as I my engine is not sitting right. I am using the mustang II motor mounts but the engine does not sit right and is off centered by a good inch. Dop the v6 INCH FRAME mounts work with the conversion or do I need the 4 cylinder...and are they different in the first place?

Any ideas? Also, any idea where to buy the needed frame mounts if they are wrong in the first place?

Thanks,
Jim
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Another V8 conversion question
« Reply #1 on: March 09, 2016, 09:13:57 AM »
I have a stock '75 V6.  I have taken the engine to rebuild it, and, yes, the engine IS offset to the passenger side.  I am not able to slide my hand down between exhaust manifold and the frame.   The only reason I can think of is to give plenty of clearance for the steering shaft.
Enzo.
Logged

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Another V8 conversion question
« Reply #2 on: March 19, 2016, 09:45:17 AM »
All the V 8 conversions I've done , I center the engine.
I've always made my own frame mounts.

However.... I have a set of front mounts I may use on the next build. Pictures and links to them : http://www.fordpinto.com/index.php?topic=22522.60
Logged

Offline 79prostreet

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +8/-0
  • Gender: Male
  • HOW GREAT IS OUR GOD!!!!

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary Photographer
Re: Another V8 conversion question
« Reply #3 on: March 19, 2016, 02:06:21 PM »
I off-set mine to leave room for steering and master cyl,one thing to remember w/ my build is that very little of the car floor was used.
Logged
79prostreet
Pages: [1]   Go Up
« previous next »