Current Classifieds

Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
77 Wagon rear hatch
Date: 12/04/2019 05:57 am
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
need a Ford battery for a 77 Pinto
Date: 02/21/2017 06:29 am
1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
Radiator
Date: 05/27/2018 06:07 am
Bellhousing for C4 to 2.0 litre pinto
Date: 01/30/2017 01:48 pm
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
Custom Pinto Project

Date: 06/12/2016 07:37 pm
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
Squire trim
Date: 03/28/2018 10:11 am

« previous next »
Pages: [1]   Go Down

Author Topic: neoprene gasket & glue?  (Read 1483 times)

0 Members and 1 Guest are viewing this topic.

Offline 79copperwagon

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
neoprene gasket & glue?
« on: April 17, 2017, 06:38:26 PM »

Anybody out there know the best glue or tack to use with a neoprene vc gasket for a 79 wagon with 2300?
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: neoprene gasket & glue?
« Reply #1 on: April 18, 2017, 07:42:42 AM »
If its a blue Felpro, no glue is necessary. The gasket is a life time rated one.
Logged
Its better to be a has-been, than a never was.

Offline 79copperwagon

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: neoprene gasket & glue?
« Reply #2 on: April 18, 2017, 01:30:58 PM »
It isn't- its a thick black Mahle-I was told by the one parts guy I should use Permatex Ultra Black & another guy wanted to sell me RTV- This is my 1st use of non-cork & its a 1 piece - if you know the engine it has that arch in the front for the timing belt so i'm having trouble keeping it in place-so any help appreciated ;)
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: neoprene gasket & glue?
« Reply #3 on: April 20, 2017, 05:15:36 PM »
Most of the rubber valve cover gaskets that I recall (similar to the 2.3 engine) typically call for a sealant at the front, inner corners where it sweeps upward over the arch. In the past I have always used RTV. Love to buy the smaller tubes at the 99 Cent only stores so I don't wind up throwing 80% of it away when it eventually hardens in the larger tube.
Logged
Pages: [1]   Go Up
« previous next »