Current Classifieds

WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
Wheel cap
Date: 04/25/2022 11:21 pm
79 pinto small parts
Date: 04/24/2019 03:16 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
Mustang II C4 Transmission
Date: 07/28/2017 06:26 am
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
Wanted Postal Pinto
Date: 09/26/2019 05:31 pm
1977 Pinto for parts

Date: 10/10/2018 06:25 pm
NEED 77/78 MUSTANG II Left Motor Mount
Date: 04/15/2017 05:14 pm
Interior Parts
Date: 08/07/2017 03:59 pm
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am

« previous next »
Pages: [1]   Go Down

Author Topic: Got no spark  (Read 1092 times)

0 Members and 1 Guest are viewing this topic.

Offline Tonycando

  • Pinto Full Member
  • ***
  • Posts: 158
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Apple User Mobile User
Got no spark
« on: March 04, 2022, 11:45:27 PM »
I’m trying to fire my Cleveland powered pinto but seem to be overlooking something , Moroso switch panel with push button start button. MSD 6 al box wired in  heavy red and black to battery small red to switched 12v source   I have the start regulator mounted in the trunk and is a full new harness going in so am I missing something coming off the I terminal from the regulator to spark this thing up.
There is no key will not be running one.
Any help will be appreciated.
Thanks
  Tony
Logged

Offline Tonycando

  • Pinto Full Member
  • ***
  • Posts: 158
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Apple User Mobile User
Re: Got no spark
« Reply #1 on: March 06, 2022, 08:23:21 PM »
Looks like I had it wired correctly but the MSD pro billet sat to long ? I’ll have to take it apart and see what’s up. I put my locked out Mallory back in and she fired right up. I’d post a vid but I always have trouble with that on this site for some reason.
Logged

Offline PintoTim2

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • '72 Pinto & '80 Pinto Pickup

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Topic Starter Mobile User
Re: Got no spark
« Reply #2 on: March 07, 2022, 07:58:26 AM »
I wonder if it was a problem with the distributor grounding through the block?   By removing the distributor and putting in the other it made connection now?   I'm not that familiar with the MSD circuits,  but the duraspark one needed a good ground to the block from the distributor.  I've seen people throw parts at this for vehicles that sat for years and it was just corroded around the distributor... . 
    Electronics (with the exception of EPROMs) usually aren't effected by time - that said, the wires and terminals do corrode but technically that's a mechanical failure - Electrons always work.
Logged

Offline Tonycando

  • Pinto Full Member
  • ***
  • Posts: 158
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Apple User Mobile User
Re: Got no spark
« Reply #3 on: March 07, 2022, 10:57:20 AM »
I took it apart and it is quite corroded internally. I’m making sure it gets cleaned up and double checking everything including my work in it as it also used to have locked out timing and I switched it back. So my rule is if it worked before I touched it then it must be something I did. Lol.
Thanks for you thoughts.
Logged
Pages: [1]   Go Up
« previous next »