Current Classifieds

1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm
1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/28/2018 09:37 am
72 pinto drag car

Date: 07/08/2017 08:25 pm
Need hatchback fuel tank sending unit
Date: 08/13/2018 02:46 pm
Looking for Plastic? sloping headlight buckets for 77/78
Date: 06/19/2018 03:58 pm
I need a 1976 hood
Date: 12/19/2016 06:02 pm
Wanted early pinto
Date: 10/03/2019 02:42 pm
1975 Pinto bumpers
Date: 10/24/2019 01:43 pm
74 hood
Date: 07/03/2017 03:46 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/12/2018 04:07 pm
SOME PARTS FOR SALE
Date: 01/11/2017 10:45 am

Author Topic: Good news for early cars...  (Read 151 times)

0 Members and 1 Guest are viewing this topic.

Offline entropy

  • Pinto Full Member
  • ***
  • Posts: 234
  • FeedBack: +13/-0
  • Gender: Male
  • Why......it's almost totally stock, of course!

  • Total Badges: 9
    Badges: (View All)
    Webmaster Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Photographer Windows User Fifth year Anniversary
Good news for early cars...
« on: June 13, 2022, 02:12:59 AM »
So, earlier this year I finally completed a total rebuild of the front suspension of my '72 V8 car.  As I'm sure you know, lower ball joints are impossible to find for these cars.  I don't mean "difficult"...I mean "can't be found at any price".  Well, not any more!  I picked up a rebuild kit from a company called Performance Suspension Technology for the early Pinto that comes with all control arm bushings, strut rod bushings, upper *and* lower ball joints, and tie rod ends...all for about $420.  Given that the last time I even *saw* lower ball joints for sale, they were NOS ones being sold for $125 each, I think you can agree that's a pretty damn good deal.

It all fits, and it all works.  I couldn't be happier with the results.

Given that all of those parts were still the 50 year old originals, and the rubber had the approximate compressive and tensile strength of pie crust, this was long overdue.  The car drives amazingly well now. A deathtrap no more!  Ok....it's still a *bit* of a deathtrap, but at least it's no longer because the suspension is completely shot and metal on metal.

Performance Suspension Technology.  Check 'em out.  Seriously. 'Cause yours is probably pretty thrashed too...
1972 "Hoonabout"
SBF swap
8" rear 4.11 posi
G-Force 5 Speed
10 point rollcage
Single stage NOS Cheater system

275 rwhp 350 lb/ft on motor.....some thing a bit more than that on the spray.

Offline dga57

  • Chief Moderator / Admin
  • FordPinto.com Moderator
  • Pinto PooBAH
  • ***
  • Posts: 7001
  • FeedBack: +208/-0
  • Gender: Male

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Windows User 1000 Posts Fifth year Anniversary
Re: Good news for early cars...
« Reply #1 on: June 13, 2022, 11:00:59 AM »
GREAT information!  Thanks so much for sharing!!!


Dwayne :)
Pinto Car Club of America - Serving the Ford Pinto enthusiast since 1999.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2401
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Good news for early cars...
« Reply #2 on: June 14, 2022, 03:14:15 PM »
I never understood why there wasn't someone who attempted to adapt a ball joint from another car. It might require welding a plate to the lower arm but for most people needing one (that is the type of people willing to keep a 50+ year old car on the road) they likely have the means (skills/tools) already to accomplish the task. I mean companies make (tubular) arms all the time and they access generic ball joints from somewhere.

BTW, over in my AMC world they used the same basic suspension for eons on the Rambler Americans. Yet for some reason the disc brakes of the 70's AMC cars like the Pacer (that are forward compatible to older front AMC American drums) seemed to change virtually every year. As such they are also in that unobtanium category. Seems these cars were too cheap to see people holding on to them and as supplies dwindled the impetus to make more was lacking.

Is there any part number or other identifier on the early Pinto lower ball joint (or associated box) that might allow someone to purchase just the ball joint and not the whole kit?

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2119
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Good news for early cars...
« Reply #3 on: June 20, 2022, 08:43:31 AM »
That will be good news for many !

I have all new OEM in the white car & all new (NOS) for two more cars, so I'm good.

Wish someone would buy my white car so I can finish the other two......