Current Classifieds

1972 Rallye wagon rebuild
Date: 11/14/2020 07:31 pm
need 1978 pinto guage cluster
Date: 03/07/2021 07:35 am
Steering Wheel Needed for 1972 Pinto
Date: 08/08/2018 12:26 pm
Free ford C3 transmission in 95695..
Date: 06/07/2021 08:14 pm
Pinto brake booster needed
Date: 05/08/2021 09:00 am
Wanted early pinto
Date: 10/03/2019 02:42 pm
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm
MISC PINTO PARTS

Date: 08/27/2017 10:23 am
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
Wagon hatch letters
Date: 12/31/2023 04:24 pm
Windshield
Date: 01/15/2022 09:31 pm
1980 Ford Pinto Squire Wagon * All original 1 Owner *

Date: 09/15/2019 12:28 pm

Author Topic: Another V8 conversion question  (Read 1136 times)

0 Members and 1 Guest are viewing this topic.

Offline jharmke

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +0/-0
  • Gender: Male
  • 77 Pinto Wagon in NJ

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User
Another V8 conversion question
« on: March 09, 2016, 08:58:30 AM »
I have seen a bunch of posts regarding V8 conversions. However, I think I hit a snag as I am converting a V6 and I think the V6 frame mounts (NOT MOTOR MOUNTS) are different from the 4 cylinder as I my engine is not sitting right. I am using the mustang II motor mounts but the engine does not sit right and is off centered by a good inch. Dop the v6 INCH FRAME mounts work with the conversion or do I need the 4 cylinder...and are they different in the first place?

Any ideas? Also, any idea where to buy the needed frame mounts if they are wrong in the first place?

Thanks,
Jim

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Another V8 conversion question
« Reply #1 on: March 09, 2016, 09:13:57 AM »
I have a stock '75 V6.  I have taken the engine to rebuild it, and, yes, the engine IS offset to the passenger side.  I am not able to slide my hand down between exhaust manifold and the frame.   The only reason I can think of is to give plenty of clearance for the steering shaft.
Enzo.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Another V8 conversion question
« Reply #2 on: March 19, 2016, 09:45:17 AM »
All the V 8 conversions I've done , I center the engine.
I've always made my own frame mounts.

However.... I have a set of front mounts I may use on the next build. Pictures and links to them : http://www.fordpinto.com/index.php?topic=22522.60

Offline 79prostreet

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +8/-0
  • Gender: Male
  • HOW GREAT IS OUR GOD!!!!

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary Photographer
Re: Another V8 conversion question
« Reply #3 on: March 19, 2016, 02:06:21 PM »
I off-set mine to leave room for steering and master cyl,one thing to remember w/ my build is that very little of the car floor was used.
79prostreet