Current Classifieds

WANTED: Skinny Rear Bumper w/o guards for '71 or '72 Pinto Coupe
Date: 04/24/2018 11:45 am
1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
Wanted Postal Pinto
Date: 08/30/2021 03:20 pm
1971-1975 Pinto
Date: 01/09/2017 04:14 pm
1978 PINTO PONY FOR SALE 17,000 ORIGINAL MILES !!!!!!!
Date: 10/10/2019 10:02 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
1973 Pinto Wagon

Date: 05/06/2022 05:13 pm
73 actuator for heater blend door
Date: 09/19/2019 04:43 pm
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
Built 2.0
Date: 10/07/2018 05:27 pm
72 Runabout for Sale- Washington

Date: 02/28/2024 02:07 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Another V8 conversion question  (Read 1185 times)

0 Members and 1 Guest are viewing this topic.

Offline jharmke

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +0/-0
  • Gender: Male
  • 77 Pinto Wagon in NJ

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User
Another V8 conversion question
« on: March 09, 2016, 08:58:30 AM »
I have seen a bunch of posts regarding V8 conversions. However, I think I hit a snag as I am converting a V6 and I think the V6 frame mounts (NOT MOTOR MOUNTS) are different from the 4 cylinder as I my engine is not sitting right. I am using the mustang II motor mounts but the engine does not sit right and is off centered by a good inch. Dop the v6 INCH FRAME mounts work with the conversion or do I need the 4 cylinder...and are they different in the first place?

Any ideas? Also, any idea where to buy the needed frame mounts if they are wrong in the first place?

Thanks,
Jim
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Another V8 conversion question
« Reply #1 on: March 09, 2016, 09:13:57 AM »
I have a stock '75 V6.  I have taken the engine to rebuild it, and, yes, the engine IS offset to the passenger side.  I am not able to slide my hand down between exhaust manifold and the frame.   The only reason I can think of is to give plenty of clearance for the steering shaft.
Enzo.
Logged

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Another V8 conversion question
« Reply #2 on: March 19, 2016, 09:45:17 AM »
All the V 8 conversions I've done , I center the engine.
I've always made my own frame mounts.

However.... I have a set of front mounts I may use on the next build. Pictures and links to them : http://www.fordpinto.com/index.php?topic=22522.60
Logged

Offline 79prostreet

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +8/-0
  • Gender: Male
  • HOW GREAT IS OUR GOD!!!!

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary Photographer
Re: Another V8 conversion question
« Reply #3 on: March 19, 2016, 02:06:21 PM »
I off-set mine to leave room for steering and master cyl,one thing to remember w/ my build is that very little of the car floor was used.
Logged
79prostreet
Pages: [1]   Go Up
« previous next »