Current Classifieds

Wanted 1973 Ford right fender
Date: 06/03/2017 08:50 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
I need a 1976 hood
Date: 12/19/2016 06:02 pm
73 Caliper Retaining Key
Date: 10/28/2021 07:49 am
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
Wanted Pinto Fiberglass Body Parts
Date: 08/16/2018 08:54 am
hood for a 79-80
Date: 11/30/2018 10:55 pm
Wheel cap
Date: 04/25/2022 11:21 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am

« previous next »
Pages: [1]   Go Down

Author Topic: Another V8 conversion question  (Read 1186 times)

0 Members and 1 Guest are viewing this topic.

Offline jharmke

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +0/-0
  • Gender: Male
  • 77 Pinto Wagon in NJ

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User
Another V8 conversion question
« on: March 09, 2016, 08:58:30 AM »
I have seen a bunch of posts regarding V8 conversions. However, I think I hit a snag as I am converting a V6 and I think the V6 frame mounts (NOT MOTOR MOUNTS) are different from the 4 cylinder as I my engine is not sitting right. I am using the mustang II motor mounts but the engine does not sit right and is off centered by a good inch. Dop the v6 INCH FRAME mounts work with the conversion or do I need the 4 cylinder...and are they different in the first place?

Any ideas? Also, any idea where to buy the needed frame mounts if they are wrong in the first place?

Thanks,
Jim
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Another V8 conversion question
« Reply #1 on: March 09, 2016, 09:13:57 AM »
I have a stock '75 V6.  I have taken the engine to rebuild it, and, yes, the engine IS offset to the passenger side.  I am not able to slide my hand down between exhaust manifold and the frame.   The only reason I can think of is to give plenty of clearance for the steering shaft.
Enzo.
Logged

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Another V8 conversion question
« Reply #2 on: March 19, 2016, 09:45:17 AM »
All the V 8 conversions I've done , I center the engine.
I've always made my own frame mounts.

However.... I have a set of front mounts I may use on the next build. Pictures and links to them : http://www.fordpinto.com/index.php?topic=22522.60
Logged

Offline 79prostreet

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +8/-0
  • Gender: Male
  • HOW GREAT IS OUR GOD!!!!

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary Photographer
Re: Another V8 conversion question
« Reply #3 on: March 19, 2016, 02:06:21 PM »
I off-set mine to leave room for steering and master cyl,one thing to remember w/ my build is that very little of the car floor was used.
Logged
79prostreet
Pages: [1]   Go Up
« previous next »