Current Classifieds

Various parts for 1980 Pony (good to N.O.S. condition
Date: 06/07/2018 01:45 am
1975 mercury bobcat

Date: 08/14/2018 03:40 pm
Intake, Head, and valve cover gasket sets

Date: 12/10/2017 01:14 pm
WTB: 2.0 Mech tach drive distributor
Date: 04/14/2023 06:15 am
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
WTB: Factory air cleaner and fan shroud 1971 2.0
Date: 02/05/2020 11:06 am
V8 rear end
Date: 04/12/2018 10:57 am
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
McLeod Clutch

Date: 04/12/2017 12:08 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
ISO instrument panel 80 hatchback
Date: 04/20/2017 08:56 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Ambitious front end project?  (Read 1179 times)

0 Members and 1 Guest are viewing this topic.

Offline entropy

  • Pinto Full Member
  • ***
  • Posts: 238
  • FeedBack: +13/-0
  • Gender: Male
  • Why......it's almost totally stock, of course!

    • Total Badges: 9
    Badges: (View All)
    Webmaster Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Photographer Windows User Fifth year Anniversary
Ambitious front end project?
« on: January 20, 2015, 11:13:19 PM »
So last year I went back to school to learn a 3D design/drafting program called Solidworks.  This semester, I'm in the advanced class and it looks like I need to come up with a big, ambitious project for my final.  Here's what I'm thinking:  What if I were to design upper and lower control arms for an early Pinto that will accept late Pinto/Mustang spindles?  The end product would be files that could carve 'em out of billet on a CNC mill.  What do you think?  Crazy idea?  Brilliant idea?  Any gurus out there who know both front ends well enough to comment?  Who wants a badass billet front suspension?! 
Logged
1972 "Hoonabout"
SBF swap
8" rear 4.11 posi
G-Force 5 Speed
10 point rollcage
Single stage NOS Cheater system

275 rwhp 350 lb/ft on motor.....some thing a bit more than that on the spray.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Ambitious front end project?
« Reply #1 on: January 21, 2015, 05:15:20 AM »
One thing you would need to find out will be the legal issues involved.

Non DOT approved / tested would be a huge concern for me.....
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Ambitious front end project?
« Reply #2 on: January 21, 2015, 07:58:30 AM »
Just from reading, it appears the late spindles will bolt up to the early suspension arms. 
http://www.fordpinto.com/general-pinto-talk/drop-spindles-on-a-73-runabout/msg129080/#msg129080
The CNC machined arms could be made stronger, add shiny components, and be a fun project.  However not sure if there would be enough demand to justify production runs and the liabilities.  The late spindle is taller (ball joint to ball joint) and would increase the angle of the early upper arm beyond stock.  If this creates too much camber gain in compression, maybe use a spacer between upper arm pivot shaft and the chassis to raise it.  I have an Excel spreadsheet with rough dimensions (tape measure) of the early and late front suspension components.  If wanted, pm me your email address and I will send it.

Note the 71-72 tie rod end is smaller than the 73-80.  So to fill the gap, a conical bushing is needed.
http://www.fordpinto.com/index.php?topic=21114.msg130207#msg130207
http://www.fordpinto.com/index.php?topic=21602.0

Logged
Jerry J - Jupiter, Florida
Pages: [1]   Go Up
« previous next »