Current Classifieds

72 pinto drag car

Date: 07/08/2017 08:53 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
Bell housing
Date: 08/23/2017 05:41 am
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
1974 Pinto Inside Rear View Mirror & Brake Pedal Pad

Date: 02/18/2017 04:41 pm
Steering Wheel Needed for 1972 Pinto
Date: 08/08/2018 12:26 pm
Need flywheel for 73 2.0 engine.
Date: 10/05/2017 02:26 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
4:11 gears for 6.75 Make offer...NEED GONE

Date: 08/01/2018 01:27 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Ambitious front end project?  (Read 1189 times)

0 Members and 1 Guest are viewing this topic.

Offline entropy

  • Pinto Full Member
  • ***
  • Posts: 238
  • FeedBack: +13/-0
  • Gender: Male
  • Why......it's almost totally stock, of course!

    • Total Badges: 9
    Badges: (View All)
    Webmaster Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Photographer Windows User Fifth year Anniversary
Ambitious front end project?
« on: January 20, 2015, 11:13:19 PM »
So last year I went back to school to learn a 3D design/drafting program called Solidworks.  This semester, I'm in the advanced class and it looks like I need to come up with a big, ambitious project for my final.  Here's what I'm thinking:  What if I were to design upper and lower control arms for an early Pinto that will accept late Pinto/Mustang spindles?  The end product would be files that could carve 'em out of billet on a CNC mill.  What do you think?  Crazy idea?  Brilliant idea?  Any gurus out there who know both front ends well enough to comment?  Who wants a badass billet front suspension?! 
Logged
1972 "Hoonabout"
SBF swap
8" rear 4.11 posi
G-Force 5 Speed
10 point rollcage
Single stage NOS Cheater system

275 rwhp 350 lb/ft on motor.....some thing a bit more than that on the spray.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Ambitious front end project?
« Reply #1 on: January 21, 2015, 05:15:20 AM »
One thing you would need to find out will be the legal issues involved.

Non DOT approved / tested would be a huge concern for me.....
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Ambitious front end project?
« Reply #2 on: January 21, 2015, 07:58:30 AM »
Just from reading, it appears the late spindles will bolt up to the early suspension arms. 
http://www.fordpinto.com/general-pinto-talk/drop-spindles-on-a-73-runabout/msg129080/#msg129080
The CNC machined arms could be made stronger, add shiny components, and be a fun project.  However not sure if there would be enough demand to justify production runs and the liabilities.  The late spindle is taller (ball joint to ball joint) and would increase the angle of the early upper arm beyond stock.  If this creates too much camber gain in compression, maybe use a spacer between upper arm pivot shaft and the chassis to raise it.  I have an Excel spreadsheet with rough dimensions (tape measure) of the early and late front suspension components.  If wanted, pm me your email address and I will send it.

Note the 71-72 tie rod end is smaller than the 73-80.  So to fill the gap, a conical bushing is needed.
http://www.fordpinto.com/index.php?topic=21114.msg130207#msg130207
http://www.fordpinto.com/index.php?topic=21602.0

Logged
Jerry J - Jupiter, Florida
Pages: [1]   Go Up
« previous next »