Current Classifieds

'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
72' hatchback parts wanted
Date: 08/25/2019 02:57 am
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
1976 Squire wagon

Date: 09/12/2018 10:30 pm
72 Pinto
Date: 03/07/2019 12:07 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
2.3 engine mounts,glove box parts,emblems,hatch,doors,hinges etc
Date: 08/26/2018 06:35 pm

Author Topic: ALUM. DRIVE SHAFTS  (Read 2813 times)

0 Members and 1 Guest are viewing this topic.

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

  • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
ALUM. DRIVE SHAFTS
« on: May 30, 2012, 08:01:32 PM »
has anyone had any luck on finding a drive shaft that is same or close to same and whats in are pintos??
thanks
eric
 
have read that awd 94-97 ford areostar rear shafts are only 1/2 in shorter
has anyone had any luck
 
thanks
 
eric
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline OhSix9

  • Pinto Full Member
  • ***
  • Posts: 248
  • FeedBack: +7/-1
  • Gender: Male
  • Positrac Intercooler Nitrous Turbo Overdrive

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: ALUM. DRIVE SHAFTS
« Reply #1 on: June 01, 2012, 12:44:01 AM »
awd Aerostar with a t5 and an 8.8 bolts right in.  didn't even have to change the yokes from the v6awd  van unit.  was 29.01 at the boneyard.

if it does measure only a half inch shorter than your original it will work fine there is lots of overlap in the slip yoke.  Word of note there are two shafts that come in those units an early and late part #  the late part # has welded ends and the early one is just pressed.  There was a recall on it so you may find the welded one on pre-96 models but avoid the ones with no welds  as they are known weak links.

OhSix'
Modest beginnings start with the single blow of a horn man..    Now when you get through with this thing every dickhead in the world is gonna wanna own it.   Do you know anything at all about the internal combustion engine?

Virgil to Sid

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

  • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: ALUM. DRIVE SHAFTS
« Reply #2 on: June 01, 2012, 03:38:29 PM »
well not going to work in my set up. 4speed with 6.3/4 rear, so if anyone is looking have one for sale, and is welded!!!! and like new. just asking what i had to spend for it 75.00
 
thanks
eric
 
 
and the u joint on the rear bolted right to my 6 3/4 rear,
 
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline vonkysmeed

  • Pinto Sr. Member
  • ****
  • Posts: 342
  • FeedBack: +4/-0
  • Gender: Male
  • 73 runabout - PCCA Ride #099
    • Project Frankenpinto

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Photographer Webmaster Tenth year Anniversary Fifth year Anniversary
Re: ALUM. DRIVE SHAFTS
« Reply #3 on: June 26, 2012, 10:57:32 PM »
fox mustang is a dead match in length.  i compared a 82 gt to the pinto
73 Pinto Runabout
351w from 74 galaxie
Heads from 69 Mercury Cougar
82 Mustang GT SROD Transmission and driveshaft
Mustang II rear end with Fairmont 3rd member
6 point cage

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2422
  • FeedBack: +70/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: ALUM. DRIVE SHAFTS
« Reply #4 on: June 27, 2012, 01:06:11 AM »
I have an early rear wheel drive aerostar DS in my 73.  The ends are pressed in so it makes it easy to shorten and press the end back.  I had mine welded to be sure that it would not spin.  The only thing I don't like about mine is that it is a 3" tube on the rear wheel drive vans where the AWD is the same diameter as the Pinto. 
vonkysmeed is correct, the AWD is the same length and dia as the fox mustangs.  I am running one in my 86 Saleen.  The original driveshaft assembly weighed 16 lbs.  I reused the mustang yoke and axle flange piece because they were smaller than the van ones.  The assembled aluminum DS weighed 7 lbs when done.  Not a bad weight savings for $40 total.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)