Current Classifieds

1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
77-78 front grill
Date: 04/07/2017 12:35 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
1972 Runabout (GOING TO SCRAP BY 5/28)

Date: 05/21/2019 11:50 am
74 hood
Date: 07/03/2017 03:46 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
Need Mustang II Manual Transmission Mount
Date: 04/21/2017 02:03 pm
need intake for oval port 2.3l
Date: 08/22/2018 09:23 am
1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 93 DIS 2.3 swap into 79 bobcat  (Read 1980 times)

0 Members and 1 Guest are viewing this topic.

Offline Hoffmanfabrications

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
93 DIS 2.3 swap into 79 bobcat
« on: July 06, 2013, 05:53:50 PM »
Hi everybody, so I'm swapping a DIS setup out of a 93 mustang into my bobcat, I'm wondering if I can delete the dash harness and just use the ECM harnes? Only problem is that I can't find any good schematics for that. Is there a way to do that or do I have to use the dash harness? I don't want to replace all the wiring. Thanks for any help.
Logged

Offline hurm2006

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • 5.0 pinto

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: 93 DIS 2.3 swap into 79 bobcat
« Reply #1 on: July 07, 2013, 09:05:55 AM »
you should be able to use the engine harness and just add your own wiring to the other side of a few of the plugs, I did this when installing a 5.0 in my car, there are a couple plugs by the master cylinder and 1 or 2 buy the ecm that need some wires hooked up (at least on the 5.0 engine harness.

here is a pinout of the 93 2.3 ecm (USE AT OWN RISK)
Logged
'77 Sedan:   fuel injected High Output 5.0, 5 speed, 26 MPG!!! daily driver

Offline Hoffmanfabrications

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: 93 DIS 2.3 swap into 79 bobcat
« Reply #2 on: July 07, 2013, 09:56:56 AM »
Thanks, I'll look into that. Gonna try n get it started this week sometime.  I like the schematic, where did u find that one? Also I have a 92 ford truck with the 5.0, how hard is it to swap that into the pinto? Just curious in case I wanna try it later on. My main goal is gas mileage, but if you are getting 26 mpg with a 5.0, I might try it!
Logged

Offline hurm2006

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • 5.0 pinto

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: 93 DIS 2.3 swap into 79 bobcat
« Reply #3 on: July 07, 2013, 01:56:45 PM »
the truck intake is way to tall to fit in a pinto, the stock mustang one is even slightly to tall, i have spacers on my hood hinges for clearance. One good information site that helped me (mostly 5.0 info) http://www.veryuseful.com/mustang/tech/
Also im using for daily driver with the 5 speed its easy to keep the rpm below 2000, with 2.73 rear gears i run about 1600 at 55-60mph
Logged
'77 Sedan:   fuel injected High Output 5.0, 5 speed, 26 MPG!!! daily driver

Offline Hoffmanfabrications

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: 93 DIS 2.3 swap into 79 bobcat
« Reply #4 on: July 11, 2013, 06:17:55 PM »
Thank you hurm2006 for your help. The schematic u provided was correct. All the wiring was the same as a 5.0 only I didn't need a few wires on the brown connector by the master cylinder. Car runs great! Haven't driven it yet, just gotta put a power steering pump on it and its ready to roll. After its all said and done, it was a lot easier than I thought it was gonna be and I'm glad I did it!!!
Logged

Offline hurm2006

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • 5.0 pinto

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: 93 DIS 2.3 swap into 79 bobcat
« Reply #5 on: July 11, 2013, 06:30:03 PM »
Glad you got it to work, its great how the engine harness is mostly self contained and you only need a few wires to make it work. The reason I did mine was that most people change the intake and slap a carb on and go. I wanted to be different but am glad I did go with the injection as the fuel mileage is great
Logged
'77 Sedan:   fuel injected High Output 5.0, 5 speed, 26 MPG!!! daily driver
Pages: [1]   Go Up
« previous next »