Current Classifieds

convert to stick
Date: 05/19/2018 09:26 pm
Looking for oil dipstick and tube 2.3L
Date: 11/23/2017 05:44 pm
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
Clutch Cable Needed
Date: 04/03/2017 11:03 pm
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/18/2017 05:55 pm
pinto parts for sale
Date: 07/25/2018 04:51 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
Need right door for pinto or bobcat 1977 to 1980 station wagon
Date: 08/03/2018 09:19 am
2 Pinto Wagons for Sale

Date: 10/29/2018 02:02 pm
1972 Pinto for sale

Date: 05/19/2021 12:41 am
Holley 4bbl carb. & Offenhauser intake.

Date: 08/09/2018 07:49 am

Author Topic: 3G alternator in a Pinto  (Read 2559 times)

0 Members and 1 Guest are viewing this topic.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
3G alternator in a Pinto
« on: April 10, 2016, 01:18:50 PM »
To install a 3G alternator in to a Pinto go look at  http://www.rothfam.com/svo/3g
Its better to be a has-been, than a never was.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: 3G alternator in a Pinto
« Reply #1 on: April 22, 2016, 07:53:42 PM »
And for anyone thinking of using a 3G alternator, there is a very good chance you'll need to use a double v-belt pulley setup or it will slip.

I had to modify the back of my stock '86 2.3T double v pulley so it wouldn't rub on the 3g's case.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline robertwwithee

  • Pinto Full Member
  • ***
  • Posts: 228
  • FeedBack: +4/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Mobile User Topic Starter
Re: 3G alternator in a Pinto
« Reply #2 on: April 23, 2016, 11:17:17 AM »
Mine worked fine with single pulley.  Have gone back to original alternator now that big stereo, lights removed.

Sent from my SPH-L720T using Tapatalk


Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: 3G alternator in a Pinto
« Reply #3 on: December 06, 2022, 08:35:11 PM »
And for anyone thinking of using a 3G alternator, there is a very good chance you'll need to use a double v-belt pulley setup or it will slip.

I had to modify the back of my stock '86 2.3T double v pulley so it wouldn't rub on the 3g's case.
Since I made that post in 2016, a fair bit has changed. At the time I was using an improvised mount on the passenger side that started life as a 1986 A/C compressor bracket.
I moved the alternator to the driver's side by use of a '77 Pinto 2.3 low-mount bracket set. A large-case 3G alternator requires grinding the lower bracket to clear a bolt boss on the case otherwise it won't rotate enough to bolt to the upper bracket. If you manage to get a twin v-belt pulley on it(I had to modify one on a lathe so it wouldn't rub the case), then only the outer groove will line-up with factory '83-86 2.3T pulleys. It will also likely need a longer belt than whatever fit on the 1G. In my case it was a 43" and it can be installed with some difficulty. Really should be 2-3" longer.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 3G alternator in a Pinto
« Reply #4 on: December 07, 2022, 12:30:53 PM »
I had to go back to the original post Dick (RIP) made to remember this. My '88 engine came with the flat belt and as I recall the alternator was mounted to one of those big, aluminum, multi mount brackets. No room (and it's ugly too) for that in a Pinto. My recollection was getting an alternator bracket from some 2.3 (likely a Pinto) that bolted to the head and then fabricating the tensioning brace from a piece of bed frame angle iron. I had to cut/bend/weld and notch it in specific places but it has worked very well. The alternator is tight to the engine and up out of the way. There is minimal wrap on the water pump pulley but cooling has never been an issue. I don't recall having alignment issues like the V-groove pulleys seem to create. I guess each situation has a method of being dealt with.