Current Classifieds

1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
Brake rotors
Date: 03/24/2017 09:02 pm
1979 Pinto Sedan Delivery

Date: 06/15/2019 03:30 pm
V8 rear end
Date: 04/12/2018 10:57 am
Pinto Wheel Well Trim
Date: 03/29/2017 11:35 am
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
73 actuator for heater blend door
Date: 09/19/2019 04:43 pm
Runabout rear window '73 to 80.
Date: 01/12/2019 10:19 am
Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
Center armrest for 1979 pinto . Possible anyone who makes them of has one for sale
Date: 08/13/2017 02:01 pm
pinto floor mats??

Date: 01/11/2017 07:27 am

Author Topic: stiffening a sway bar with angle iron?  (Read 1379 times)

0 Members and 1 Guest are viewing this topic.

Offline carbomb

  • Pinto Member
  • **
  • Posts: 75
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver
    • yea

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Fifth year Anniversary Webmaster
stiffening a sway bar with angle iron?
« on: January 01, 2012, 07:02:31 PM »
I know you can buy bigger sway bars for pintos but i would rather spend my money on other things! I was wondering if there is anything very wrong with welding angle iron on the straight part of a sway bar? That would be where all the torsion and twisting occurs so if you welded a little reinforcement to it it should make stiffer and handle better. Right? I have coilovers on the back and it stays pretty flat just the front sway bar needs to be stiffer. We have a 220 mig so we could really melt it in and get good penetration. Just woundering if anybody has tried this or has any reasons not to.

RSM

  • Guest
Re: stiffening a sway bar with angle iron?
« Reply #1 on: January 01, 2012, 07:26:30 PM »
Are you road racing or something?

Offline postalpony

  • Pinto Full Member
  • ***
  • Posts: 201
  • FeedBack: +30/-0
  • Gender: Male
  • WHEN IN DOUBT--BUILD IT STOUT!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary Photographer
Re: stiffening a sway bar with angle iron?
« Reply #2 on: January 01, 2012, 07:33:28 PM »
Hi carbomb
1st don't weld on your swaybar. They are heat treated to effect torsional forces, & if you
weld on it the heat from the arc may cause the bar to break. This is just my opinion from
my 45+ years in industrial maintenance.    Dick
1980 Hatchback was a "Postal Unit" on the
west coast in it's early life. Now residing
in Ohio, But we don't haul the U.S. Mail anymore;
 Now all we do is HAUL!
 5th gear 4700 rpm & still pullin'= 113+  mph
 
 UPDATE-83.762 mph in 4th gear As verified by a W Va State Trooper-WITH 1 GEAR TO GO 6-2-11

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: stiffening a sway bar with angle iron?
« Reply #3 on: January 01, 2012, 08:30:43 PM »
also as far as i know the bars are hollow!
1973 pinto runabout