Current Classifieds

Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
1978 hatch back

Date: 11/29/2019 03:18 pm
Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am
Early V8 swap headers, damaged, fixable?
Date: 10/25/2019 03:30 pm
79 pinto small parts
Date: 04/24/2019 03:16 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
1975 Pinto bumpers
Date: 10/24/2019 01:45 pm
1976 Squire wagon

Date: 09/12/2018 10:30 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?  (Read 1952 times)

0 Members and 1 Guest are viewing this topic.

Offline Sir Thomas Crapper

  • Pinto Member
  • **
  • Posts: 23
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?
« on: March 19, 2015, 07:39:24 AM »
I'm trying to dig up info, but I remember seeing somewhere that a 1.6L Pinto engine is a "kent" and that a 2.0 Zetec has the kent bell housing bolt pattern.

Long story longer, I have a free Zx2 at my brother's house, and can pick up a cheap 1.6/4 speed.. Free Zetec + cheap 4 speed= WIN???

Please help me make this happen.
Logged

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?
« Reply #1 on: March 19, 2015, 02:54:22 PM »
I think this link will provide some help; http://www.retro-ford.co.uk/shop/content/fitting-zetec-mk-12-escort-type-9-gearbox .
The MK1/2 European Ford Escort is relatively close in design to the Pinto with crossflow engine,  a lot of the problems that you are also going to run into are carefully explained here.
For most problems they have fixes, but you'll see that it all adds up rather quickly.
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?
« Reply #2 on: March 20, 2015, 12:56:32 PM »
I found this info while researching a V6 project.  I don't know if the "EAO" is the kent motor.
 
Ford Pinto EAO I4 pattern
·   1.6L/2.0L EAO I4

Ford Canadian Essex FWD pattern
·   2.3/2.5L HSC FWD I4
·   2.3L HSO FWD I4
·   3.0L Vulcan V6 (FWD and RWD)
·   3.0/3.2L SHO V6
·   3.8/3.9/4.2L Canadian Essex 90 degree FWD V6

Ford Pinto OHC RWD pattern
·   1.3/1.6/1.8/2.0/2.3/2.5L OHC I4 RWD

Logged

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?
« Reply #3 on: March 21, 2015, 03:57:13 PM »
  • [size=78%]From what I remember ,back then the Kent engine (1600 pinto) had the same bolt patern as the 2000 pinto German engine, then the later 2.3 Lima engine , only the alignment dowels were larger, the later 2.3 bell housings got taller and used the upper two bolt holes on the block, they all took the same size pilot bearing, [/size]
  • [/size]
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Roadrace Squire, will a 1.6L 4 speed trans bolt up to a Zetec?
« Reply #4 on: March 27, 2015, 03:53:22 AM »
How to mount the zetec? They have no side motor mount pads at all, they mount on front cam belt cover.
Logged
Pages: [1]   Go Up
« previous next »