Current Classifieds

t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
Rear brake shoes

Date: 01/23/2017 05:01 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
1979 hatch needed
Date: 05/13/2018 08:52 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm
1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm

Recent Posts

Pages: 1 ... 8 9 [10]
91
Your Project / Re: Pinto Powered Mustang Roadster
« Last post by dga57 on January 12, 2024, 09:42:27 AM »
Looking at it is better than not looking at it!  lol   Happy New Year!!!

Dwayne :)
92
General Help- Ask the Experts... / Re: My last week here
« Last post by dga57 on January 12, 2024, 09:40:43 AM »
Welcome aboard Brent!  So glad to know that Bob went to a good home. 

Dwayne :)
93
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by george graves on January 11, 2024, 02:21:35 PM »
Ha!  Thanks!  I'm glad you like it. They are also really fun to make with kids - they LOVE it.
94
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by caravan3921 on January 11, 2024, 09:16:15 AM »
This made my day and brought the biggest smile to my face!
Love it!
95
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by george graves on January 10, 2024, 05:34:04 PM »
...
96
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by george graves on January 10, 2024, 03:27:57 PM »
Thanks!  You can find them here if you would like to pick up a set:  https://www.carcookiecutters.com/products/ford-pinto-cookie-cutter-set
97
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by rob289c on January 10, 2024, 06:18:51 AM »
Very nice!  My wife bakes and decorates cookies for a living.  We have bags and bags of cookie cutters but no Pintos!
98
General Pinto Talk / Re: I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by alwaysFlOoReD on January 09, 2024, 09:30:25 PM »
That's awesome!
99
General Help- Ask the Experts... / Re: stumble/lag
« Last post by Wittsend on January 09, 2024, 02:21:36 PM »
 Is the choke open (warm engine) or partially closed (cold engine)? Maybe a low float setting? If the level is low it may take a delayed time for the fuel to pull through the venturi. It might be low due to a weak fuel pump or a clog that is BARELY getting enough fuel to idle and squirt the accelerator pump - only. If everything is stock that car might have a De-Cel valve and it might be getting triggered to bleed air when the throttle is opened. I'm not familiar with those (always gets removed) but others have reported problems with them.

Are you sure the engine is running on all cylinders? When I got my 73, 2.0 one cylinder wasn't firing. It drove but very slowly. I found the valve seats had worn to the point there there was zero lash on some of the valves and compression was very low. Setting the lash to specs got all cylinders above 100 though not equal. Hope one of those helps.
100
General Pinto Talk / I made some Pinto Cookie Cutters - thought you guys would get a kick out of them
« Last post by george graves on January 09, 2024, 12:18:46 PM »
Pages: 1 ... 8 9 [10]