Current Classifieds

76 drivers fender
Date: 07/20/2018 08:24 pm
Dumping '80 yellow Pinto

Date: 06/21/2017 03:45 pm
Pinto Watch

Date: 06/22/2019 07:12 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
pinto wagon parts
Date: 12/19/2019 01:43 pm
1980 pinto wagon for sale
Date: 12/11/2017 12:13 am
Mustang ll/Pinto/Bobcat Aluminum Wheel Rim

Date: 07/20/2018 03:00 pm
Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
1978 hatch back

Date: 11/29/2019 03:18 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
1975 mercury bobcat

Date: 08/14/2018 03:40 pm

Recent Posts

Pages: [1] 2 3 ... 10
1
General Help- Ask the Experts... / Re: Pinto California Emissions Questions
« Last post by TIGGER on Yesterday at 04:05:27 PM »
I owned a 78 Cal-emissions HB about 13-14 years ago.  It still had all the emissions stuff installed, an 89K little old lady car.  Unfortunately I do not have any detailed pictures of the engine and vacuum lines.  I did create a detailed thread on my dad's 79 wagon with the vacuum line routing.  It is a 4cyl 4spd, non cal-emissions car though.  Even though it is different, maybe the thread will be helpful?  Good luck to you.


Vacuum Connections for a 79 4cyl. (fordpinto.com)
2
General Help- Ask the Experts... / Re: First timer, dash pad question
« Last post by TIGGER on Yesterday at 02:45:45 PM »
I saw on FB yesterday that someone had a black dash pad for sale. I assume crack free but I did not read it.  I believe it was $320 if I remember correctly.
3
General Help- Ask the Experts... / Re: Schoenfeld headers
« Last post by fordblue72 on April 16, 2024, 08:47:59 AM »
My brother put that header on his 71… had to modify the mount but it worked out fine.
4
General Help- Ask the Experts... / Re: Schoenfeld headers
« Last post by rob289c on April 14, 2024, 05:52:24 AM »
I'm glad yours bolted right up.  On the Pacesetter header I bought, I had to heat and beat (basically flatten) the #3 tube to provide clearance between it and the right side frame rail.  I also had to remove and re-position the right side brace.  It looks cool but I wished it would have been a true bolt-on installation.  What I thought should take 15-30 minutes took the better part of an afternoon and it was in a fairly bare chassis!
5
General Help- Ask the Experts... / Re: Schoenfeld headers
« Last post by Milescabbathway on April 13, 2024, 08:06:45 PM »
Yes!  Bolted right up with no other mods.  2.5” all the way back sounds great too
6
Pintos or Bobcats FOR SALE / 1977 Pinto Cruizin Wagon
« Last post by Vicrydr on April 11, 2024, 04:13:17 PM »
1977 Pinto Cruizin Wagon

Selling my Pinto wagon because of health reasons. Shiny orange paint. 83,8xx miles on chassis. Has 1986 Ford Ranger 2.3L EFI engine with less than 1K on overhaul. 4 speed manual trans. Front floorpans replaced.New front carpet with 88 Thunderbird turbocoupe bucket seats. Nearly new 13" tires on original rims. New tie rods. Have the following that will go with this sale- 5 speed trans from 88 turbocoupe, 5 speed trans from 86 ranger pickup, original 77 pinto 2.3L engine, 88 Thunderbird turbo engine with computer box, original pinto bucket seats that are in need of upholstery, all other misc. parts. The tach and speedo gauge housing has been reworked and will not fall apart. Gas tank has been cleaned and resealed. Runs and drives good. Can send more pics on request.

More Information
7
Pintos or Bobcats FOR SALE / 1977 Pinto Cruizin Wagon
« Last post by Vicrydr on April 11, 2024, 03:56:24 PM »
1977 Pinto Cruizin Wagon

Selling my Pinto wagon because of health reasons. Shiny orange paint. 83,8xx miles on chassis. Has 1986 Ford Ranger 2.3L EFI engine with less than 1K on overhaul. 4 speed manual trans. Front floorpans replaced.New front carpet with 88 Thunderbird turbocoupe bucket seats. Nearly new 13" tires on original rims. New tie rods. Have the following that will go with this sale- 5 speed trans from 88 turbocoupe, 5 speed trans from 86 ranger pickup, original 77 pinto 2.3L engine, 88 Thunderbird turbo engine with computer box, original pinto bucket seats that are in need of upholstery, all other misc. parts. The tach and speedo gauge housing has been reworked and will not fall apart. Gas tank has been cleaned and resealed. Runs and drives good. Can send more pics on request.

More Information
8
Your Project / Re: Pinto Powered Mustang Roadster
« Last post by dga57 on April 06, 2024, 07:58:14 AM »
Quote from: rob289c on April 06, 2024, 07:20:31 AM
I will hopefully start posting progress again soon. 

Definitely looking forward to it!

Dwayne :)
9
Your Project / Re: Pinto Powered Mustang Roadster
« Last post by rob289c on April 06, 2024, 07:20:31 AM »
We had snow this week but the trend is for improving weather patterns.  Hopefully I can transform my Winter storage barn into an operating shop soon.  I need to get back on my project so I can get it done this Summer.  I have priming and painting to do so I need it to really warm up.  There are some other odds and ends I can do until it's warm enough to paint so I will hopefully start posting progress again soon. 
10
Parts Resources, Here is where you can find this or that. / Re: New turn switch
« Last post by warhead2 on April 04, 2024, 07:57:58 PM »
That works too

Sent from my SM-G965U using Tapatalk

Pages: [1] 2 3 ... 10