Current Classifieds

1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
1974 Pinto Door Handles

Date: 03/07/2017 04:06 pm
'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Esslinger 2.0 intake
Date: 03/06/2017 11:58 am
1974 points distributor for 2.3l
Date: 07/04/2022 07:55 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
Needed, 2.0 or 2.3 motors
Date: 09/30/2018 07:47 pm
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am
Wanted '75 Bobcat Instrument Cluster & Wiring Harness
Date: 12/09/2018 06:59 am
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm
Wanted 73 pinto squire wagon
Date: 05/09/2020 11:59 am
Bumper Guards
Date: 03/28/2017 09:27 pm

« previous next »
Pages: [1]   Go Down

Author Topic: What Would I Need to Install this T-5?  (Read 2377 times)

0 Members and 1 Guest are viewing this topic.

Offline Henrius

  • Pinto Full Member
  • ***
  • Posts: 162
  • FeedBack: +4/-0
  • Gender: Male
    • Three Pillars blog

    • Total Badges: 7
    Badges: (View All)
    Webmaster Tenth year Anniversary Topic Starter Signature Windows User Apple User Fifth year Anniversary
What Would I Need to Install this T-5?
« on: April 09, 2014, 12:02:47 PM »
A mechanic friend of mine was going to give me a Borg-Warner T-5 from a Chevy S-10. He said he has searched all his parts books and cannot find a bell housing for the T-5 that will fit the Pinto 2.0 liter motor.


I need to know if I should take this tranny from him (offered for free!), and what parts I would need to adapt it to my 1973 Pinto with a 2.0 liter and 4 speed.


Kim Henry


henrius@mindsapring.com
Logged
1973 Pinto Runabout with upgraded 2.0 liter & 4 speed, and factory sunroof. My first car, now restored, and better than it was when it rolled off the assembly line!

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: What Would I Need to Install this T-5?
« Reply #1 on: April 09, 2014, 02:17:08 PM »
It wont fit. I forget the list of reasons but a few are wrong input shaft, mounting pad, shifter location & driveshaft yoke. There are more reasons besides those. Also the T5 overdrive is nearly useless behind a stock 2.0 unless you want to run a steeper rear gear
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline Henrius

  • Pinto Full Member
  • ***
  • Posts: 162
  • FeedBack: +4/-0
  • Gender: Male
    • Three Pillars blog

    • Total Badges: 7
    Badges: (View All)
    Webmaster Tenth year Anniversary Topic Starter Signature Windows User Apple User Fifth year Anniversary
Re: What Would I Need to Install this T-5?
« Reply #2 on: April 13, 2014, 10:55:21 AM »
It isn't a stock 2.0. I significantly increased HP.


What is it about this S-10 T-5 that is different than the other T-5 conversions I see on this forum?


Is it that one T-5 was built to fit a 2.3 liter in the Mustang, and also happens to fit the 2.0 in the Pinto?
Logged
1973 Pinto Runabout with upgraded 2.0 liter & 4 speed, and factory sunroof. My first car, now restored, and better than it was when it rolled off the assembly line!

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: What Would I Need to Install this T-5?
« Reply #3 on: April 13, 2014, 11:42:02 AM »
S-10 has a LOW first gear for pulling stumps out of the ground like a good truck should. Get one out of a Fox body Mustang and the bell housing will fit a 2.0L with step dowel pins.
Logged
Its better to be a has-been, than a never was.
Pages: [1]   Go Up
« previous next »