Current Classifieds

1972 Runabout (GOING TO SCRAP BY 5/28)

Date: 05/21/2019 11:50 am
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
1972 Pinto for sale

Date: 05/19/2021 12:41 am
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
pintos for sale
Date: 12/11/2018 04:29 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
LOTS OF 1971-1973 PARTS FOR SALE
Date: 02/03/2018 11:28 am

« previous next »
Pages: [1]   Go Down

Author Topic: Hood/Carb clearance and go fast  (Read 3306 times)

0 Members and 1 Guest are viewing this topic.

Offline lesterwa58

  • Pinto Member
  • **
  • Posts: 28
  • FeedBack: +0/-0

    • Total Badges: 4
    Badges: (View All)
    Tenth year Anniversary Topic Starter Windows User Fifth year Anniversary
Hood/Carb clearance and go fast
« on: April 15, 2013, 07:19:00 PM »
I am installing a Motorcraft/Ford 2 barrel carburator on an Offenhauser intake manifold in my 1980 Pinto with a 2300 engine, will I have a problem with hood clearance, and if so what can I do to allow the hood close normally?  If I need to modify the hood, where/who might I go to for another hood?  Without going into the engine, other than the top part, what can I do further to give me more go power?  I have the Offenhauser intake manifold and carb, an exhaust header and a roller cam with a competition grind?  Please respond to me via my e-mail address, which is: lesterwa58@yahoo.com
Logged

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: Hood/Carb clearance and go fast
« Reply #1 on: May 19, 2013, 10:11:44 PM »
I'm curious about this too.  I have an offenhauser dual port intake with a fuel injection set up from FAST.  I'm hoping it all fits underneath the hood.  Planning on having the heads done at BoPort racing and a roller cam as well. 
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Hood/Carb clearance and go fast
« Reply #2 on: September 23, 2013, 01:12:52 AM »
Yes, the post is old, but I'd be curious to know how much trouble came of using the Motorcraft 2 bbl., if it is a 2100 or 2150. Should have some fits there with too rich due to power valve issues, depending on which carb used.
Logged

Offline moonman

  • Pinto Member
  • **
  • Posts: 24
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Fifth year Anniversary
Re: Hood/Carb clearance and go fast
« Reply #3 on: January 09, 2014, 11:18:46 PM »
i have run an offy intake with a 390 holly 4 barrel and a mr gasket air filter for a year no problem.
Logged
streets the game, sneaks the game love to go fast in Little cars.

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Re: Hood/Carb clearance and go fast
« Reply #4 on: January 09, 2014, 11:57:26 PM »
There is a low profile air cleaner with a drop down base that might work.
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Hood/Carb clearance and go fast
« Reply #5 on: January 10, 2014, 09:35:34 AM »
The triangle shape air cleaner with all the holes in the top, that Edelbrock sells will clear ever thing just fine. Cheap too.
Logged
Its better to be a has-been, than a never was.
Pages: [1]   Go Up
« previous next »