Current Classifieds

hubcaps

Date: 10/31/2018 12:04 pm
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
v8 springs
Date: 05/07/2017 04:46 pm
WTB Manual Transmission Clutch Pedal for '78
Date: 03/29/2019 07:20 am
1978 PINTO PONY FOR SALE 17,000 ORIGINAL MILES !!!!!!!
Date: 10/10/2019 09:42 pm
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
1972 pinto grill
Date: 02/27/2018 12:13 am
Wanted '75 Bobcat Instrument Cluster & Wiring Harness
Date: 12/09/2018 06:59 am
pinto floor mats??

Date: 01/11/2017 07:27 am

« previous next »
Pages: [1]   Go Down

Author Topic: Glass hatch  (Read 2707 times)

0 Members and 1 Guest are viewing this topic.

Offline yhalkeeiron

  • Pinto Member
  • **
  • Posts: 36
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Apple User Mobile User
Glass hatch
« on: February 02, 2014, 12:42:47 AM »
Does anybody know if a 79 glass hatch will fit on a 73 run about

Sent from my SPH-L710 using Tapatalk

Logged

RSM

  • Guest
Re: Glass hatch
« Reply #1 on: February 02, 2014, 12:58:01 AM »
It will not.
Logged

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2424
  • FeedBack: +70/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Glass hatch
« Reply #2 on: February 03, 2014, 08:25:17 PM »
Just curious, what you say it will not fit?  I put a 79 bobcat full metal hatch on my 72 that I had years ago.  It bolted on just fine.  And other than having the holes for Mercury, it was the same. 
 
Maybe it is because the gasket? The early cars, the gasket was glued in where the later ones had to slip over the pinch weld.  The glass hatch had a special gasket.  He might need to modify the lip to get it to fit.
 
That is the only think I can think of.  In my opinion, the rest of the pieces should bolt in.
Logged
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: Glass hatch
« Reply #3 on: February 06, 2014, 03:39:12 PM »
I think it should fit fine but a few holes may need drilled depending on the upper hinge & prop shocks. The seal should fit the 73
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline derekrichmond15@yahoo.com

  • Pinto Member
  • **
  • Posts: 72
  • FeedBack: +0/-0
  • Gender: Male
  • 408 stroker

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Mobile User Poll Voter Windows User
Re: Glass hatch
« Reply #4 on: August 03, 2014, 01:32:48 PM »
I just did the swap to my 77 from a 80 doner car all was ez and gained rer defrost it all plugged into the wiring no splicing good luck!!
Logged
1977 408W stroked pinto
Pages: [1]   Go Up
« previous next »