Current Classifieds

Wheel cap
Date: 04/25/2022 11:21 pm
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
71-73 sway bar
Date: 06/12/2021 10:12 am
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
13" Style Steel Trim Rings

Date: 10/09/2020 10:35 pm
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
Drip rail chrome
Date: 01/14/2017 09:18 am
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
1978 ford pinto carb
Date: 02/04/2018 06:09 pm
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm

« previous next »
Pages: [1]   Go Down

Author Topic: can trans/motor be pulled/installed as one unit?  (Read 2472 times)

0 Members and 1 Guest are viewing this topic.

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
can trans/motor be pulled/installed as one unit?
« on: May 02, 2016, 04:29:14 AM »
Hi,    I have a 72' Runabout with the 1.6 and FOG transmission.  I bought it with the trans already removed, I have since pulled the motor and would like to install both together if possible.  Looks too tight though.  Is this doable?  Thanks for any info.
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #1 on: May 02, 2016, 11:01:37 AM »
No experience in trying both together, but having put a 2.3 in my 73 Pinto I'm inclined to say no.  Many years ago I replaced the throwout bearing in my brothers 72, 1.6.  As I recall getting the transmission in/out was not difficult.   I remember when I pulled the 2.0 to install the 2.3.  I think I had the engine out in 20 minutes.  So, I can understand why you would like to install the engine/trans as a unit, but doing in two steps isn't that difficult.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: can trans/motor be pulled/installed as one unit?
« Reply #2 on: May 14, 2016, 10:45:27 AM »
I put the 2.3 and T5 in my '72 together as a unit and the 2.0/4spd came out that way. You'll need a load leveler and an engine hoist that can go pretty high.
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #3 on: May 14, 2016, 03:38:52 PM »
Yes it can be , that one is the easy one to pull ,  also that is how the factory installs them , all in one peace ,
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0
Pages: [1]   Go Up
« previous next »