Current Classifieds

Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am
Mirror
Date: 04/15/2020 01:42 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
1977 Pinto Cruizin Wagon

Date: 08/07/2023 02:52 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
Ignition switch 72 pinto wagon 2.0 4 sp
Date: 12/31/2017 09:03 pm
Sunroof shade
Date: 06/19/2019 01:33 pm
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
1978 RUNABOUT

Date: 04/01/2017 03:18 pm
72 pinto drag car

Date: 07/08/2017 08:53 pm
1979 Pinto 3-door Runabout *PRICE REDUCED*

Date: 08/01/2023 06:53 pm

« previous next »
Pages: [1]   Go Down

Author Topic: can trans/motor be pulled/installed as one unit?  (Read 2478 times)

0 Members and 1 Guest are viewing this topic.

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
can trans/motor be pulled/installed as one unit?
« on: May 02, 2016, 04:29:14 AM »
Hi,    I have a 72' Runabout with the 1.6 and FOG transmission.  I bought it with the trans already removed, I have since pulled the motor and would like to install both together if possible.  Looks too tight though.  Is this doable?  Thanks for any info.
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #1 on: May 02, 2016, 11:01:37 AM »
No experience in trying both together, but having put a 2.3 in my 73 Pinto I'm inclined to say no.  Many years ago I replaced the throwout bearing in my brothers 72, 1.6.  As I recall getting the transmission in/out was not difficult.   I remember when I pulled the 2.0 to install the 2.3.  I think I had the engine out in 20 minutes.  So, I can understand why you would like to install the engine/trans as a unit, but doing in two steps isn't that difficult.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: can trans/motor be pulled/installed as one unit?
« Reply #2 on: May 14, 2016, 10:45:27 AM »
I put the 2.3 and T5 in my '72 together as a unit and the 2.0/4spd came out that way. You'll need a load leveler and an engine hoist that can go pretty high.
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #3 on: May 14, 2016, 03:38:52 PM »
Yes it can be , that one is the easy one to pull ,  also that is how the factory installs them , all in one peace ,
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0
Pages: [1]   Go Up
« previous next »