Current Classifieds

WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
73 Runabout

Date: 11/20/2017 03:19 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
MISC PINTO PARTS

Date: 08/27/2017 10:23 am
'80 Pinto Wagon
Date: 02/01/2018 05:20 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
1973 Pinto Wagon

Date: 05/06/2022 05:13 pm
71-73 sway bar
Date: 06/12/2021 10:12 am

« previous next »
Pages: [1]   Go Down

Author Topic: can trans/motor be pulled/installed as one unit?  (Read 2473 times)

0 Members and 1 Guest are viewing this topic.

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
can trans/motor be pulled/installed as one unit?
« on: May 02, 2016, 04:29:14 AM »
Hi,    I have a 72' Runabout with the 1.6 and FOG transmission.  I bought it with the trans already removed, I have since pulled the motor and would like to install both together if possible.  Looks too tight though.  Is this doable?  Thanks for any info.
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #1 on: May 02, 2016, 11:01:37 AM »
No experience in trying both together, but having put a 2.3 in my 73 Pinto I'm inclined to say no.  Many years ago I replaced the throwout bearing in my brothers 72, 1.6.  As I recall getting the transmission in/out was not difficult.   I remember when I pulled the 2.0 to install the 2.3.  I think I had the engine out in 20 minutes.  So, I can understand why you would like to install the engine/trans as a unit, but doing in two steps isn't that difficult.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: can trans/motor be pulled/installed as one unit?
« Reply #2 on: May 14, 2016, 10:45:27 AM »
I put the 2.3 and T5 in my '72 together as a unit and the 2.0/4spd came out that way. You'll need a load leveler and an engine hoist that can go pretty high.
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: can trans/motor be pulled/installed as one unit?
« Reply #3 on: May 14, 2016, 03:38:52 PM »
Yes it can be , that one is the easy one to pull ,  also that is how the factory installs them , all in one peace ,
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0
Pages: [1]   Go Up
« previous next »