Current Classifieds

74 pinto
Date: 09/11/2016 06:32 pm
2.3 engine and other parts- Free
Date: 12/13/2016 10:25 am
1980 Pinto Wagon

Date: 02/29/2020 07:01 pm
1972 Runabout (GOING TO SCRAP BY 5/28)

Date: 05/21/2019 11:50 am
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
6.6.75 carrier
Date: 02/14/2018 06:47 am
1978 Pinto Wagon V8
Date: 04/28/2023 03:26 pm
74 hood
Date: 07/03/2017 03:46 pm
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
Pinto Runabout wanted
Date: 06/05/2018 04:42 pm
Anyone scrapping a 1980
Date: 03/13/2020 08:46 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Rubber Coil spring isolator  (Read 1391 times)

0 Members and 1 Guest are viewing this topic.

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 242
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

    • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Rubber Coil spring isolator
« on: April 17, 2019, 01:46:47 AM »
I bought from Speedway Motors
https://www.speedwaymotors.com -
coil spring isolators for a 77 Mustang 2. I took measurements from my 30+ yr old isolator where very close match.
Inside diameter
Old 3.21 to 3.28
New 3.18
Outside diameter
Old 4.80 to 4.87
New 4.69
Now the old one has been smashed and has stretched in 30+yrs so the measurements are a little off. But the new one rubber is very pliable and should fit very snugly. I paid 25.53 with shipping and that is for 2. One for each side. Im dont know if this will work before 77 just have to check measurements. Hopefully this will help people out. Part number in picture.

Sent from my SAMSUNG-SM-G930A using Tapatalk
Logged

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Rubber Coil spring isolator
« Reply #1 on: April 17, 2019, 06:56:35 AM »
Good post !

I changed the front springs in my 72. Don't remember the year of Mll they were for.
They were for an Mll V8 with AC.
Cut them down (measurement in shop).
Same size as OEM, except longer stronger.

They look like a perfect "gift" you could send to me for the boots  ;D
Logged

Offline cossiepinto

  • Pinto Full Member
  • ***
  • Posts: 174
  • FeedBack: +13/-0
  • Gender: Male
  • Howdy

    • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Rubber Coil spring isolator
« Reply #2 on: April 17, 2019, 07:15:57 AM »
I bought a set of urethane spring pads a few years back for the Cosworth Pinto to adjust ride height, but never used them.  I think they were about 1 inch thick.  I saw them the other day while clearing out my shop.  I did a quick search at Summit, but didn't find them with a lazy search (at work).
If anyone is interested in them, contact me. I think I can find them again.
Logged

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 242
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

    • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Rubber Coil spring isolator
« Reply #3 on: April 19, 2019, 02:25:51 AM »
They fit nice and snug. didn't have to fight to put them on.

Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged
Pages: [1]   Go Up
« previous next »