Current Classifieds

pinto parts for sale
Date: 07/25/2018 04:51 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
FREE PARTS!!

Date: 01/10/2017 02:38 pm
2.3 engine mounts,glove box parts,emblems,hatch,doors,hinges etc
Date: 08/26/2018 06:35 pm
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm
1979/80 Pinto needs to be saved
Date: 09/10/2018 10:41 pm
ford pinto door panels
Date: 03/20/2022 07:51 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am
ford pinto door panels
Date: 03/20/2022 07:51 pm
Drip rail chrome
Date: 01/14/2017 09:18 am
Wanted instrument cluster lens for 74
Date: 04/30/2023 04:31 pm

Author Topic: Pinto Column Turn Signal Switch  (Read 2141 times)

0 Members and 1 Guest are viewing this topic.

Offline lesterwa58

  • Pinto Member
  • **
  • Posts: 28
  • FeedBack: +0/-0

  • Total Badges: 4
    Badges: (View All)
    Tenth year Anniversary Topic Starter Windows User Fifth year Anniversary
Pinto Column Turn Signal Switch
« on: June 24, 2017, 08:19:32 PM »
I have a 1980 Pinto Squire built in Sept of 1979,that I need a new turn signal switch for.  I have bought what was supposed to be a new Ford replacement switch, Part #REPF505802, but this does not fit.  Therefore there has to be another switch that would fit my application, but I cannot locate one.  I really need this switch as my left turn signal does not work, yes the bulbs and flasher have been checked/replaced.  Please advise asto where I might look.
Wes Jones, Cle Elum, WA

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Pinto Column Turn Signal Switch
« Reply #1 on: June 24, 2017, 08:55:33 PM »
Sometimes it's not the switch , but a few ways to check it , the bulb socket could have a broken wire inside or poor ground , quick way to check is to turn on the emergency flashers , it bypasses the turn switch , so if all flash it's the switch , if not it's a wiring/connection problem .
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Pinto Column Turn Signal Switch
« Reply #2 on: June 25, 2017, 11:11:50 AM »
Try ford pinto nos for hard to find parts.
Its better to be a has-been, than a never was.

Offline Nytshaed

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Female
  • So, now I own a Pinto....

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Poll Voter Signature
Re: Pinto Column Turn Signal Switch
« Reply #3 on: June 14, 2018, 10:26:36 AM »
Hello!  I am also fighting turn signal issues. I did the Hazard button test, and the driver's side still does not blink, or work with brakes, all three other corners blink. So, wiring and light bulb socket will be checked next I guess.
Queen of Purple
Goddess of Glow in the Dark
Keeper of the "Green Coconut" 1972 Ford Pinto

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Pinto Column Turn Signal Switch
« Reply #4 on: June 14, 2018, 10:46:45 AM »
In most cases bad grounds are the problem of most light/signal problems.  The system depends on the fact that the cars steel body itself is the ground wire.  40+ years of corrosion is generally the problem.  You can clean the connection point, but typically they become bare steel and eventually corrode again.  I've resorted to soldering a wire to the light socket and then anchoring it to somewhere in the car body less likely to corrode.  In some cases I've actually soldered it at both ends if I can do so without damaging the body paint.

Offline Nytshaed

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Female
  • So, now I own a Pinto....

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Poll Voter Signature
Re: Pinto Column Turn Signal Switch
« Reply #5 on: June 14, 2018, 10:59:08 AM »
Thanks for the tips, I will pass that along to my hubby who's volunteered to get her tip top running. After that we are going to do a full repaint in the original metallic lime to go over some shoddy work on the driver's door and about 500 dabs of "Paint Touch Up Pen" that make it look worse than if the chips had been left alone.
Queen of Purple
Goddess of Glow in the Dark
Keeper of the "Green Coconut" 1972 Ford Pinto

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Pinto Column Turn Signal Switch
« Reply #6 on: June 14, 2018, 11:44:29 PM »
Sometimes the grease on the contacts of the turn signal lever (at the steering column)  can dry over time and also cause and electrical problem. So, it is another area to check.  Hope you get it sorted.