Current Classifieds

Intake manifolds

Date: 03/06/2021 03:04 pm
Front sway bar

Date: 07/23/2018 08:19 pm
78 windshield trim
Date: 02/01/2020 08:46 am
convert to stick
Date: 05/19/2018 09:26 pm
WANTED: Skinny Rear Bumper w/o guards for '71 or '72 Pinto Coupe
Date: 04/24/2018 11:45 am
Steering Wheel Needed for 1972 Pinto
Date: 08/08/2018 12:26 pm
1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am
1974 Pinto Right Rear Interior Trim Panel

Date: 02/18/2017 04:44 pm
74 pinto
Date: 09/11/2016 06:32 pm
1975 mercury bobcat

Date: 08/14/2018 03:40 pm
71-73 Front Kick Panels
Date: 04/25/2021 07:24 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am

Author Topic: Heater Delete Plate  (Read 864 times)

0 Members and 1 Guest are viewing this topic.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Heater Delete Plate
« on: November 01, 2016, 06:22:09 AM »
Maybe. You can see I posted asking for info: http://www.boss302.com/smf/index.php?topic=73661.0

Thoughts ?

I've searched all over for a short (flat ?)motor. No luck. Even called GE asking & they said without a part number, no go , as they would have to look at hundreds to match up.

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Heater Delete Plate
« Reply #1 on: November 01, 2016, 06:27:18 PM »
For a shorter blower motor, Wittsend used a MG Midget motor and JohnW used a 89 Turbo Carvan motor, see links.  I have not seen it done but maybe using a radiator electric cooling fan pancake motor with some R&D.  Pinto's with factory AC had the blower motor located inside the car and a flat engine bay cover where Freon pipes enter, see ebay photo (I do not see the second hose but it gets the idea across).
http://www.fordpinto.com/index.php?topic=22899.msg139619#msg139619
http://www.fordpinto.com/index.php?topic=24959.msg152749#msg152749
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Heater Delete Plate
« Reply #2 on: November 01, 2016, 07:56:23 PM »
For clarity the MG fan I used needs to run backwards (simply reverse polarity) and I used the MG fan cage also. The cage spins backwards but I felt it moved sufficient air. But, do note I live in So. Cal. and heating requirements are lower here than other places. As is obvious this was necessary for a Turbo 2.3 swap, but I see you are doing a V-8 swap.  I agree with Jerry (Old Kayaker) there are many options with heater motors. Mounting  the motor is relatively simple as they typically only have 2 or 3 screws.

I stumbled upon the MG fan only because we used them as replacement motors in our Sunbeam Tigers. I had done the swap, but never put the housing back in the car.  Then when it became obvious the Pinto needed clearance ... the rest is history.