Current Classifieds

1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm
pro stock front end
Date: 06/28/2019 07:43 pm
Want side to side luggage rack rails for '75 Pinto wagon
Date: 08/30/2018 12:59 am
I have a 1977 Cobra body lots of parts here
Date: 04/12/2017 06:57 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
2.3 engine and other parts- Free
Date: 12/13/2016 10:25 am
Electrical
Date: 03/29/2017 11:37 am
72 Turbo Pinto "Hot Rod" rebuild
Date: 08/09/2018 11:09 am
79 pinto driveshaft
Date: 08/18/2018 02:03 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Heater Delete Plate  (Read 888 times)

0 Members and 1 Guest are viewing this topic.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Heater Delete Plate
« on: November 01, 2016, 06:22:09 AM »
Maybe. You can see I posted asking for info: http://www.boss302.com/smf/index.php?topic=73661.0

Thoughts ?

I've searched all over for a short (flat ?)motor. No luck. Even called GE asking & they said without a part number, no go , as they would have to look at hundreds to match up.
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Heater Delete Plate
« Reply #1 on: November 01, 2016, 06:27:18 PM »
For a shorter blower motor, Wittsend used a MG Midget motor and JohnW used a 89 Turbo Carvan motor, see links.  I have not seen it done but maybe using a radiator electric cooling fan pancake motor with some R&D.  Pinto's with factory AC had the blower motor located inside the car and a flat engine bay cover where Freon pipes enter, see ebay photo (I do not see the second hose but it gets the idea across).
http://www.fordpinto.com/index.php?topic=22899.msg139619#msg139619
http://www.fordpinto.com/index.php?topic=24959.msg152749#msg152749
Logged
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Heater Delete Plate
« Reply #2 on: November 01, 2016, 07:56:23 PM »
For clarity the MG fan I used needs to run backwards (simply reverse polarity) and I used the MG fan cage also. The cage spins backwards but I felt it moved sufficient air. But, do note I live in So. Cal. and heating requirements are lower here than other places. As is obvious this was necessary for a Turbo 2.3 swap, but I see you are doing a V-8 swap.  I agree with Jerry (Old Kayaker) there are many options with heater motors. Mounting  the motor is relatively simple as they typically only have 2 or 3 screws.

I stumbled upon the MG fan only because we used them as replacement motors in our Sunbeam Tigers. I had done the swap, but never put the housing back in the car.  Then when it became obvious the Pinto needed clearance ... the rest is history.
Logged
Pages: [1]   Go Up
« previous next »