Current Classifieds

ISO instrument panel 80 hatchback
Date: 04/20/2017 08:56 pm
13" Style Steel Trim Rings

Date: 10/09/2020 10:35 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
Mini Mark IV one of 2 delux lg. sunroof models
Date: 06/18/2018 03:47 pm
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am

« previous next »
Pages: [1]   Go Down

Author Topic: Heater Delete Plate  (Read 889 times)

0 Members and 1 Guest are viewing this topic.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Heater Delete Plate
« on: November 01, 2016, 06:22:09 AM »
Maybe. You can see I posted asking for info: http://www.boss302.com/smf/index.php?topic=73661.0

Thoughts ?

I've searched all over for a short (flat ?)motor. No luck. Even called GE asking & they said without a part number, no go , as they would have to look at hundreds to match up.
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Heater Delete Plate
« Reply #1 on: November 01, 2016, 06:27:18 PM »
For a shorter blower motor, Wittsend used a MG Midget motor and JohnW used a 89 Turbo Carvan motor, see links.  I have not seen it done but maybe using a radiator electric cooling fan pancake motor with some R&D.  Pinto's with factory AC had the blower motor located inside the car and a flat engine bay cover where Freon pipes enter, see ebay photo (I do not see the second hose but it gets the idea across).
http://www.fordpinto.com/index.php?topic=22899.msg139619#msg139619
http://www.fordpinto.com/index.php?topic=24959.msg152749#msg152749
Logged
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Heater Delete Plate
« Reply #2 on: November 01, 2016, 07:56:23 PM »
For clarity the MG fan I used needs to run backwards (simply reverse polarity) and I used the MG fan cage also. The cage spins backwards but I felt it moved sufficient air. But, do note I live in So. Cal. and heating requirements are lower here than other places. As is obvious this was necessary for a Turbo 2.3 swap, but I see you are doing a V-8 swap.  I agree with Jerry (Old Kayaker) there are many options with heater motors. Mounting  the motor is relatively simple as they typically only have 2 or 3 screws.

I stumbled upon the MG fan only because we used them as replacement motors in our Sunbeam Tigers. I had done the swap, but never put the housing back in the car.  Then when it became obvious the Pinto needed clearance ... the rest is history.
Logged
Pages: [1]   Go Up
« previous next »