Current Classifieds

1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
1600 CC WATER PUMP
Date: 06/02/2018 09:13 am
Pinto drive train

Date: 06/29/2018 08:32 am
74 Wagon body parts and a couple of 79 bits

Date: 11/14/2019 04:02 am
1979 hatch needed
Date: 05/13/2018 08:52 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
Looking for leaf spring insulators
Date: 04/04/2020 09:38 am
Wanted early pinto
Date: 10/03/2019 02:42 pm
Automatic Wagon
Date: 06/14/2019 11:22 pm
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm

Author Topic: rear end  (Read 2398 times)

0 Members and 1 Guest are viewing this topic.

Offline Loner

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
rear end
« on: July 09, 2017, 10:33:34 PM »
Hi All.  Long story short I have an old Lehman trike. I have a problem with the rear end. Was told it was early Pinto. I need left axle and spider gear. But not sure witch one it is. What i have. rear drop out, 8 bolt, square pan. (not octegon) 4 lug with drum brakes. I also think that it is 2.73 gears. Any ideas?Would rather talk on phone if possible. Took me all afternoon to get this far.
   Loner  559 310 5792

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2351
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: rear end
« Reply #1 on: July 10, 2017, 08:45:27 PM »
In reply to the other post where you stated you were confused. http://www.fordpinto.com/general-help/rear-end-by-loner-(reply-to-locked-thread)/msg175065/?topicseen#new

  I'm not sure what has you confused? But, I will basically restated what I said before incrementally.

1. There were two different rear ends used in Pinto's.

2. One type is the 6-3/4" which sounds like what you describe. There is a removable rear cover. However, a picture would be helpful to decide that is actually what you really have. Or, you can do a Google image search.

3. The other type is the 8", it has a smooth rounded cover that is not removable and the gears are accessed by a section removable from the front.

4. There are no specific Pinto parts dealers like there might be for a classic Mustang or Camaro. There are a few individuals that sell parts they have acquired.  Asking specifically here would be a start but frankly this board has very low activity. So, you may not get any response, or it may take some time. Update - Case in point: 48 hours have passed (see image) since I replied to your initial, locked post with a separate post..., Dewayne the Administrator then unlock and moved your post and I have re-answered your post at this new location on the Forum. In that 48 hour time period the three most recent posts are all three of those actions. Like I said, it can be slow.

5. It is likely difficult to find someone just selling the axle or spider gear.

6.  You would probably more easily find someone selling a whole 6-3/4" rear end but that is a heavy item and costly to ship.  If you let people know where you are located (in general) you have a better chance of getting a reply if they know you are near by.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 756
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: rear end
« Reply #2 on: July 29, 2017, 09:10:05 AM »
8 bolt, square pan. (not octegon)

That tells me it's not a 6.75in Pinto rear end. Pintos only came with two options: either a 6.75in integral carrier (with an eight-sided cover) or the ubiquitous Ford 8in with a drop-out third member.

I have a 6.75 diff and axles I'm not going to use, but wouldn't stock Pinto axles be too wide for a trike anyway?
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: rear end
« Reply #3 on: July 29, 2017, 10:22:02 AM »
My 80 Pinto with a 6 3/4" rear end has a square shape cover on the rear end. Check the bolt pattern on the axles to see if its 4 1/4".
Its better to be a has-been, than a never was.