Current Classifieds

Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
Front grill for '72
Date: 03/02/2022 12:09 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm
Various parts for 1980 Pony (good to N.O.S. condition
Date: 06/07/2018 01:45 am
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
Wagon rear quarters
Date: 06/17/2020 03:32 pm
78 hatchback

Date: 03/12/2023 06:50 pm
Wanted hood hinges
Date: 02/17/2020 05:30 pm

Author Topic: What are ya'll doing for intercoolers?  (Read 3510 times)

0 Members and 1 Guest are viewing this topic.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
What are ya'll doing for intercoolers?
« on: May 30, 2014, 06:11:26 PM »
I searched. Believe me, I search before starting a new thread. ;D

I'm still gathering info for my 2.3T swap. The engine I have is out an '86 'Bird, so it's not intercooled and I will likely run it that way for a while. However, I want to unlock the full 205hp potential of the setup and that means using an IC. I have an '87-88 'Bird IC that might be useful with custom tanks.

Catch #1: I want to avoid cutting up the radiator support, so that means routing tubes through the big oval hole on the passenger side, which means an intercooler with in/out on the same side.

Catch #2: I want to fit an A/C condenser somewhere between the grille and radiator too. I was thinking about an intercooler on one side and a condenser on the other rather than placing one in front of the other as is usually done. I haven't yet looked to see what sizes and shapes of condensers are available and/or suitable.

Anyone with experience or ideas doing something similar? Suggestions, critique, etc are welcome.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline don33

  • Pinto Sr. Member
  • ****
  • Posts: 280
  • FeedBack: +5/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Fifth year Anniversary Poll Voter Windows User
Re: What are ya'll doing for intercoolers?
« Reply #1 on: June 01, 2014, 06:53:43 PM »
I cut the rad support, But, I'm pretty sure you can use the Large NPR IC. without cutting, it is a pretty good IC, works Well... I like the NPR because its well designed for a minimal IC tubing setup.

Offline Bigtimmay

  • Pinto Sr. Member
  • ****
  • Posts: 710
  • FeedBack: +8/-0
  • Gender: Male
  • Everythings better with boost!

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary Mobile User Windows User
Re: What are ya'll doing for intercoolers?
« Reply #2 on: June 05, 2014, 01:44:22 PM »
you have to cut the rad support some to put in a npr for where the tubes run through but you can keep the top of the support and the hood latch and all that stuff. and a npr bolts in the same spot as the radiator.
1978 Mercury Bobcat 2.3t swapped.Always needs more parts!

Offline L.D

  • Pinto Member
  • **
  • Posts: 46
  • FeedBack: +16/-0
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Windows User Linux User Mobile User
Re: What are ya'll doing for intercoolers?
« Reply #3 on: June 10, 2014, 11:39:12 PM »
what year and size of npr intercoolers are you guys running?