Current Classifieds

Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
2.0 Mickey Thompson SUPER RARE Rocker cover and belt guard
Date: 08/22/2017 09:21 pm
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
72 Pinto
Date: 03/07/2019 12:07 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
1971 Pinto Runabout turn key driver

Date: 12/04/2018 07:40 pm
C-3 automatic transmission

Date: 08/17/2022 10:18 am
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
WTB Manual Transmission Clutch Pedal for '78
Date: 03/29/2019 07:20 am

Author Topic: A 1972 turbo swap adventure  (Read 95914 times)

0 Members and 1 Guest are viewing this topic.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: My 1972 turbo swap thread
« Reply #300 on: December 23, 2022, 08:13:24 PM »
I think that is the first time I've seen the turbo exhaust fit (much less at a generous 3") with the factory fan motor! That is quite a feat. I used the MG motor/fan that gets run backwards with the factory set up. Marginal but something is better than nothing. I believe there was a modern Dodge fan someone else said worked too.
I should point out before anyone gets their hopes up that the fan motor pictured is in fact a shorter VDO PM3652 unit. I had it on the shelf and was forced to use it when I installed the current Frankenstein turbo; a Borg-Warner S2B with a Chinese Garrett/Ford T3 housing machined to fit on it. The turbine outlet bolt pattern was rotated about 10° from the stock location and moved the wastegate elbow rearward at least 3/8 of an inch I didn't really have.

The downpipe layout I have now would probably hit a stock fan motor. It would be much easier to notch for clearance though.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: A 1972 turbo swap adventure
« Reply #301 on: January 07, 2023, 08:34:13 PM »
I got the exhaust essentially done this evening. It was done a week ago, but the v-band flanges warped from welding and were leaking. They are the lipped stainless flanges, so sanding them flat would be a lot of work and not guarantee anything. Instead I made some small gaskets out of desoldering wick (woven copper ribbon) and coated them with high-temp RTV. Seems to have done the job.
I had to use the actuator from a Chinese ebay turbo that the wastegate assembly came from because the flapper post is bigger than the stock one. I could tell it has a stiffer spring and after setting it up with stock preload, it makes 15psi on the gate alone. That's alright, but I'd prefer having the 10psi option and will have to make a new end that fits the old actuator threads and the new flapper.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.