Current Classifieds

Holley 4bbl carb. & Offenhauser intake.

Date: 08/09/2018 07:49 am
78 pinto wagon

Date: 03/03/2020 01:07 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
1975 Pinto wagon emissions decal wanted
Date: 09/20/2018 11:01 pm
1975 mercury bobcat

Date: 08/14/2018 03:40 pm
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
Gazelle Replicar Pinto powered frame

Date: 01/28/2017 12:30 pm
Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
Clutch Cable Needed
Date: 04/03/2017 11:03 pm

« previous next »
Pages: [1]   Go Down

Author Topic: going from a 2.0 4 spd to a T 2.3/T5 List of parts?  (Read 2667 times)

0 Members and 1 Guest are viewing this topic.

Offline Sir Thomas Crapper

  • Pinto Member
  • **
  • Posts: 23
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
going from a 2.0 4 spd to a T 2.3/T5 List of parts?
« on: September 25, 2014, 08:55:11 AM »
Is there a list of what is needed to do the swap?  Will the pinto 2.3 motor mounts work for this?  I picked up a 2.3 oil pan and pump, is this necessary to change over?

I remember reading that a stock fox body mustang driveshaft is the right length, but you need to install a new rear u joint.   

Are there any links to builds?
Logged

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2501
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: going from a 2.0 4 spd to a T 2.3/T5 List of parts?
« Reply #1 on: September 25, 2014, 09:27:44 AM »
There is not a parts list per say, but I did a write up on my conversion.  You should be able to glean most from it:

http://www.fordpinto.com/general-pinto-talk/so-you-want-to-build-a-turbo-pinto-part-1/msg76893/#msg76893

http://www.fordpinto.com/general-pinto-talk/so-you-want-to-build-a-turbo-pinto-part-2/msg76894/?topicseen#msg76894

Bill, who goes by "JoeBob" did one also. And there are currently a number of people in progress who are reporting on theirs. "65ShelbyClone" being one of them.

I assume with the 2.0 you have an early, thin bumper car? My article should help as it is based on a '73 conversion. If you have a '74 2.0 then there are some modification that you don't have to do since the 2.3 was an engine choice in '74 and up.
Logged
Pages: [1]   Go Up
« previous next »