Current Classifieds

Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm
Parts Parts Parts
Date: 09/08/2018 03:13 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:41 am
1975 Ford Pinto

Date: 01/13/2020 11:02 am
1979 hatch needed
Date: 05/13/2018 08:52 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
1976 pinto for sale

Date: 01/12/2017 02:08 pm
2.8 radiator
Date: 10/25/2019 04:10 pm
2.3 engine and other parts- Free
Date: 12/13/2016 10:25 am

Author Topic: 88 Turbo coupe going in a 79  (Read 3223 times)

0 Members and 1 Guest are viewing this topic.

Offline sponge003

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
88 Turbo coupe going in a 79
« on: October 20, 2013, 06:34:24 PM »
Putting a 88 Tbird turbo coupe motor (That was in a ranger) in a 79 to race in the 24 hours of lemons and have a couple of questions

The donor motor has a ranger aluminum oil pan and 5 speed (Mazda), anybody tried to stuff this combo in a pinto?? It looks like it will be pretty tight and the pan is rear sump versus front.

What do you do for fuel lines?? It has some of the plastic lines from the T bird near the engine.

we have the 8.8 from the same year T Bird, looks just a bit (~2") wider. This is a track only car so we can massage the quarters within reason.

We have stripped the car down and working on the roll cage etc.

I tried the search feature and didn't get any results I was looking for

Appreciate the help

Offline Pinturbo75

  • Pinto Sr. Member
  • ****
  • Posts: 722
  • FeedBack: +26/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #1 on: October 20, 2013, 10:21:35 PM »
you need a pinto pan and pickup and dipstick...., the rear will work if you want to use it.... I swapped out the axles for a set from a stang and used the stang drum brakes.... it narrowed the rear 1.5 inches.... as long as you get the spring pads welded on at the same pinion angle as the pinto rear was youre good.... that's what I did.
75 turbo pinto trunk, megasquirt2, 133lb injectors, bv head, precision 6265 turbo, 3" exhaust,bobs log, 8.8, t5,, subframe connectors, 65 mm tb, frontmount ic, traction bars, 255 lph walbro,
73 turbo pinto panel wagon, ms1, 85 lb inj, fmic, holset hy35, 3" exhaust, msd, bov,

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #2 on: October 20, 2013, 10:45:41 PM »
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom

Offline sponge003

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: 88 Turbo coupe going in a 79
« Reply #3 on: October 20, 2013, 10:53:30 PM »
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom

What year F150 pump? That would solve another issue!!

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #4 on: October 21, 2013, 10:40:58 AM »
Sorry I don't exactly know.  I got it at U-Pick Parts for $11.  Given the age of the cars/trucks there I'd say late 80's.   It is about 2" in diameter and about 8" long.  It sits in a stamped steel housing that is insulated to prevent vibration. Here is a picture.  The reddish stuff is battery terminal seal to prevent corrosion for the pump ground.


Offline JohnW

  • Pinto Full Member
  • ***
  • Posts: 229
  • FeedBack: +5/-0
  • Gender: Male
  • 1980 Runabout

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Poll Voter
Re: 88 Turbo coupe going in a 79
« Reply #5 on: December 08, 2013, 09:33:52 PM »
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom
They definitely work but god do they zoop to put on. I had to do one in my Ranger when I snapped a line replacing my fuel filter, it cooled halfway through and I had to keep splashing hot water on and trying to force it further.

Use really hot water and push it on as quick as you can.
-