Current Classifieds

2 Station Wagons for sale
Date: 04/20/2018 11:10 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
Seeking 1971-1973 Rotors
Date: 04/08/2021 12:23 pm
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
77 Wagon rear hatch
Date: 12/04/2019 05:57 am
1972 pinto grill
Date: 02/27/2018 12:13 am
Seeking 1971-1973 Rotors
Date: 04/08/2021 12:23 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
1979 Pinto Sedan Delivery

Date: 06/15/2019 03:30 pm
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
1975 Pinto bumpers
Date: 10/24/2019 01:43 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 88 Turbo coupe going in a 79  (Read 3256 times)

0 Members and 1 Guest are viewing this topic.

Offline sponge003

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
88 Turbo coupe going in a 79
« on: October 20, 2013, 06:34:24 PM »
Putting a 88 Tbird turbo coupe motor (That was in a ranger) in a 79 to race in the 24 hours of lemons and have a couple of questions

The donor motor has a ranger aluminum oil pan and 5 speed (Mazda), anybody tried to stuff this combo in a pinto?? It looks like it will be pretty tight and the pan is rear sump versus front.

What do you do for fuel lines?? It has some of the plastic lines from the T bird near the engine.

we have the 8.8 from the same year T Bird, looks just a bit (~2") wider. This is a track only car so we can massage the quarters within reason.

We have stripped the car down and working on the roll cage etc.

I tried the search feature and didn't get any results I was looking for

Appreciate the help
Logged

Offline Pinturbo75

  • Pinto Sr. Member
  • ****
  • Posts: 722
  • FeedBack: +26/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #1 on: October 20, 2013, 10:21:35 PM »
you need a pinto pan and pickup and dipstick...., the rear will work if you want to use it.... I swapped out the axles for a set from a stang and used the stang drum brakes.... it narrowed the rear 1.5 inches.... as long as you get the spring pads welded on at the same pinion angle as the pinto rear was youre good.... that's what I did.
Logged
75 turbo pinto trunk, megasquirt2, 133lb injectors, bv head, precision 6265 turbo, 3" exhaust,bobs log, 8.8, t5,, subframe connectors, 65 mm tb, frontmount ic, traction bars, 255 lph walbro,
73 turbo pinto panel wagon, ms1, 85 lb inj, fmic, holset hy35, 3" exhaust, msd, bov,

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #2 on: October 20, 2013, 10:45:41 PM »
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom
Logged

Offline sponge003

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: 88 Turbo coupe going in a 79
« Reply #3 on: October 20, 2013, 10:53:30 PM »
Quote from: Wittsend on October 20, 2013, 10:45:41 PM
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom

What year F150 pump? That would solve another issue!!
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 88 Turbo coupe going in a 79
« Reply #4 on: October 21, 2013, 10:40:58 AM »
Sorry I don't exactly know.  I got it at U-Pick Parts for $11.  Given the age of the cars/trucks there I'd say late 80's.   It is about 2" in diameter and about 8" long.  It sits in a stamped steel housing that is insulated to prevent vibration. Here is a picture.  The reddish stuff is battery terminal seal to prevent corrosion for the pump ground.

Logged

Offline JohnW

  • Pinto Full Member
  • ***
  • Posts: 229
  • FeedBack: +5/-0
  • Gender: Male
  • 1980 Runabout

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Poll Voter
Re: 88 Turbo coupe going in a 79
« Reply #5 on: December 08, 2013, 09:33:52 PM »
Quote from: Wittsend on October 20, 2013, 10:45:41 PM
I used the '88 Turbo Coupe lines.  From the external pump (Ford F-150) I ran the factory line. I had to cut it in at least one spot.  They sell a special barbed repair connector where I did the cut.  Basically you put the plastic line in hot water then with all your might force it over the connector.  You would think without clamps it would leak or blow apart but 4 years later so far so good.

Tom
They definitely work but god do they zoop to put on. I had to do one in my Ranger when I snapped a line replacing my fuel filter, it cooled halfway through and I had to keep splashing hot water on and trying to force it further.

Use really hot water and push it on as quick as you can.
Logged
-
Pages: [1]   Go Up
« previous next »